manualshive.com logo in svg

DaimlerChrysler Jeep Grand Cherokee 2002, Руководство по обслуживанию

Поделиться
Скачать
DaimlerChrysler Jeep Grand Cherokee 2002 Скачать руководство пользователя страница 190

Symptom:

P1270-INTAKE PORT SWIRL ACTUATOR OPEN CIRCUIT

When Monitored and Set Condition:

P1270-INTAKE PORT SWIRL ACTUATOR OPEN CIRCUIT

When Monitored:

With the ignition on.

Set Condition:

The ECM does not detect voltage on the Intake Port Swirl Actuator

Control circuit.

POSSIBLE CAUSES

INTERMITTENT CONDITION

ASD RELAY OUTPUT CIRCUIT OPEN

SWIRL SOLENOID CONTROL CIRCUIT SHORTED TO GROUND

SWIRL SOLENOID CONTROL CKT OPEN

SWIRL SOLENOID

ENGINE CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, erase ECM DTCs.
With the DRBIII

t

, actuate the Swirl Solenoid.

Monitor the DRB for ECM DTCs.
Did this DTC set again?

All

Yes

→

Go To

2

No

→

Go To

6

2

Turn the ignition off.
Disconnect the Swirl Solenoid harness connector.
Turn the ignition on.
Using a 12-volt test light connected to ground, check the ASD Relay Output circuit.
Does the test light illuminate brightly?

All

Yes

→

Go To

3

No

→

Repair the ASD Relay Output circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2.

3

Turn the ignition off.
Disconnect the Swirl Solenoid harness connector.
Disconnect the ECM harness connectors.
Measure the resistance between ground and the Swirl Solenoid Control circuit.
Is the resistance above 1000 ohms?

All

Yes

→

Go To

4

No

→

Repair the Swirl Solenoid Control circuit for a short to ground.
Perform ROAD TEST VERIFICATION - VER-2.

182

DRIVEABILITY - DIESEL

ProCarManuals.com

Содержание Jeep Grand Cherokee 2002





























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды