manualshive.com logo in svg

DaimlerChrysler Jeep Grand Cherokee 2002, Руководство по обслуживанию

Поделиться
Скачать
DaimlerChrysler Jeep Grand Cherokee 2002 Скачать руководство пользователя страница 146

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Disconnect the MAF Sensor harness connector.
Turn the ignition on.
Measure the voltage of the Sensor Reference Voltage A circuit.
Is the voltage above 4.8 volts?

All

Yes

→

Replace the Mass Air Flow Sensor.
Perform ROAD TEST VERIFICATION - VER-2.

No

→

Go To

4

4

Turn the ignition off.
Disconnect the Accelerator Pedal Position Sensor harness connector.
Turn the ignition on.
Measure the voltage of the Sensor Reference Voltage A circuit.
Is the voltage above 4.8 volts?

All

Yes

→

Replace the Accelerator Pedal Position Sensor.
Perform ROAD TEST VERIFICATION - VER-2.

No

→

Go To

5

5

Turn the ignition off.
Disconnect the ECM harness connectors.
Disconnect the MAF Sensor and Accelerator Pedal Position Sensor harness connec-
tors.
Measure the resistance between ground and the Sensor Reference Voltage A circuit.
Is the resistance above 100 kohms?

All

Yes

→

Go To

6

No

→

Repair the Sensor Reference Voltage A circuit for a short to
ground.
Perform ROAD TEST VERIFICATION - VER-2.

6

Turn the ignition off.
Disconnect the ECM harness connectors.
Disconnect the MAF Sensor harness connector.
Measure the resistance between the Sensor Reference Voltage A circuit and the MAF
Sensor Ground circuit.
Disconnect the Accelerator Pedal Position Sensor harness connector.
Measure the resistance between the Sensor Reference Voltage A circuit and both
Accelerator Pedal Position Sensor Ground circuits.
Is the resistance above 100 kohms for each measurement?

All

Yes

→

Go To

7

No

→

Repair the Sensor Reference Voltage A circuit for a short to the
Sensor Ground circuit that measured below 100 kohms.
Perform ROAD TEST VERIFICATION - VER-2.

138

DRIVEABILITY - DIESEL

P0641-SENSOR REFERENCE VOLTAGE A CKT VOLTAGE TOO LOW —

Continued

ProCarManuals.com

Содержание Jeep Grand Cherokee 2002





























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды