manualshive.com logo in svg

DaimlerChrysler Jeep Grand Cherokee 2002, Руководство по обслуживанию

Поделиться
Скачать
DaimlerChrysler Jeep Grand Cherokee 2002 Скачать руководство пользователя страница 66

Symptom:

P0235-BOOST PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW

When Monitored and Set Condition:

P0235-BOOST PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW

When Monitored:

With the ignition on.

Set Condition:

The Turbocharger Boost Pressure Sensor Signal voltage is below 0.30 volt

for at least 2 seconds.

POSSIBLE CAUSES

INTERMITTENT CONDITION

5-VOLT SUPPLY CIRCUIT OPEN

BOOST PRESSURE SENSOR

BOOST PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO GROUND

BOOST PRESSURE SENSOR SIGNAL AND GROUND CIRCUITS SHORTED TOGETHER

BOOST PRESSURE SENSOR SIGNAL CIRCUIT OPEN

ENGINE CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, read the Turbocharger Boost Pressure Sensor voltage.
Is the voltage below 0.3 volt?

All

Yes

→

Go To

2

No

→

Go To

8

2

Turn the ignition off.
Disconnect the Boost Pressure Sensor harness connector.
Turn the ignition on.
Measure the voltage between ground and the 5-volt Supply circuit.
Is the voltage above 4.9 volt?

All

Yes

→

Go To

3

No

→

Repair the 5-volt Supply circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2.

3

Turn the ignition off.
Disconnect the Boost Pressure Sensor harness connector.
Turn the ignition on.
Connect a jumper wire between the Boost Pressure Sensor Signal and 5-volt Supply
circuits.
With the DRB, read the Boost Pressure Sensor voltage.
Is the Boost Pressure Sensor voltage above 4.5 volts?

All

Yes

→

Replace the Boost Pressure Sensor.
Perform ROAD TEST VERIFICATION - VER-2.

No

→

Go To

4

58

DRIVEABILITY - DIESEL

ProCarManuals.com

Содержание Jeep Grand Cherokee 2002





























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды