manualshive.com logo in svg

DaimlerChrysler Jeep Grand Cherokee 2002, Руководство по обслуживанию

Поделиться
Скачать
DaimlerChrysler Jeep Grand Cherokee 2002 Скачать руководство пользователя страница 87

TEST

ACTION

APPLICABILITY

6

Turn the ignition off.
Disconnect the CMP Sensor harness connector.
Disconnect the ECM harness connectors.
Measure the resistance of the Sensor Ground circuit between the CMP Sensor
harness connector and the ECM harness connector.
Is the resistance below 10.0 ohms?

All

Yes

→

Go To

7

No

→

Repair the Sensor Ground circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2.

7

Turn the ignition on.
Disconnect the IAT Sensor harness connector.
Disconnect the Camshaft Position Sensor harness connector.
Connect one end of a jumper wire to the IAT Sensor signal circuit in the IAT Sensor
harness connector.
Connect the other end of the jumper wire to the Sensor Ground circuit in the
Camshaft Position Sensor harness connector.
With the DRBIII

t

in Engine, Sensors, read the Intake Air Temp volts.

Is the voltage below 1.0 volt?

All

Yes

→

Go To

8

No

→

Replace and program the ECM in accordance with the Service
Information.
Perform ROAD TEST VERIFICATION - VER-2.

8

Turn the ignition off.
Remove the CMP Sensor.
Inspect the camshaft for conditions such as loose mounting screws, damage, debris or
cracked teeth.
Is there any evidence of these conditions?

All

Yes

→

Repair as necessary.
Perform ROAD TEST VERIFICATION - VER-2.

No

→

Go To

9

9

Turn the ignition off.
With the DRBIII

t

lab scope lead, backprobe the CMP Signal circuit.

Set the DRBIII

t

lab scope settings as follows: Time = 0.1s/Div, 20 volts scale, Offset

= 0.00volts, Probe = X10, Coupling = DC.
While observing the DRBIII

t

display, crank the engine.

NOTE: The DRBIII

t

should display a digital signal (square wave) similar to

that shown in the support material.
Does the DRBIII

t

display an uninterrupted digital signal (square wave)?

All

Yes

→

Replace and program the Engine Control Module in accordance
with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

No

→

Replace the Camshaft Position Sensor in accordance with the
Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

79

DRIVEABILITY - DIESEL

P0340-CMP/CKP POSITION SENSOR CIRCUIT - SIGNAL FREQUENCY
TOO HIGH —

Continued

ProCarManuals.com

Содержание Jeep Grand Cherokee 2002





























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды