manualshive.com logo in svg

DaimlerChrysler Jeep Grand Cherokee 2002, Руководство по обслуживанию

Поделиться
Скачать
DaimlerChrysler Jeep Grand Cherokee 2002 Скачать руководство пользователя страница 32

TEST

ACTION

APPLICABILITY

13

Turn the ignition off.
Disconnect the MAF Sensor harness connector.
Disconnect the ECM harness connectors.
Measure the resistance between ground and the Sensor Reference Voltage A circuit
at the MAF harness connector.
Is the resistance below 1000 ohms?

All

Yes

→

Repair the Sensor Reference Voltage A circuit for a short to
ground.
Perform ROAD TEST VERIFICATION - VER-2.

No

→

Go To

14

14

Turn the ignition off.
Disconnect the MAF Sensor harness connector.
Disconnect the ECM harness connectors.
Remove the ASD Relay from the PDC.
Connect a jumper wire between cavity 30 and cavity 87 of the ASD Relay connector.
Turn the ignition on.
Measure the voltage of the Sensor Reference Voltage A circuit in the ECM harness
connector.
Is the voltage above 1.0 volt?

All

Yes

→

Repair the Sensor Reference Voltage A circuit for a short to
voltage.
Perform ROAD TEST VERIFICATION - VER-2.

No

→

Go To

15

15

Turn the ignition off.
Disconnect the Fuel Pressure Sensor harness connector.
Disconnect the ECM harness connectors.
Measure the resistance between the 5-volt Supply circuit and the Sensor Ground
circuit at the Fuel Pressure Sensor harness connector.
Is the resistance above 1000 ohms?

All

Yes

→

Go To

16

No

→

Repair the Fuel Pressure Sensor 5-volt Supply circuit for a short
to the Sensor Ground circuit.
Perform ROAD TEST VERIFICATION - VER-2.

16

Turn the ignition off.
Disconnect the Fuel Pressure Sensor harness connector.
Disconnect the ECM harness connectors.
Measure the resistance between ground and the 5-volt Supply circuit at the Fuel
Pressure Sensor harness connector.
Is the resistance below 1000 ohms?

All

Yes

→

Repair the Fuel Pressure Sensor 5-volt Supply circuit for a short
to ground.
Perform ROAD TEST VERIFICATION - VER-2.

No

→

Go To

17

24

DRIVEABILITY - DIESEL

P0100-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO HIGH —

Continued

ProCarManuals.com

Содержание Jeep Grand Cherokee 2002





























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды