manualshive.com logo in svg

DaimlerChrysler Jeep Grand Cherokee 2002, Руководство по обслуживанию

Поделиться
Скачать
DaimlerChrysler Jeep Grand Cherokee 2002 Скачать руководство пользователя страница 86

TEST

ACTION

APPLICABILITY

1

NOTE: The Timing Belt must be correctly installed and operational before
diagnosis can be made. Refer to the Service Information to ensure the
timing belt is properly installed.
Turn the ignition on.
With the DRBIII

t

, erase the ECM DTCs.

Attempt to start the engine.
With the DRBIII

t

, read the ECM DTCs.

Does the DRBIII

t

display this DTC?

All

Yes

→

Go To

3

No

→

Go To

2

2

Turn the ignition on.
With the DRBIII

t

, erase the ECM DTCs.

Test drive the vehicle.
With the DRBIII

t

, read the ECM DTCs.

Does the DRBIII

t

display this DTC?

All

Yes

→

Go To

3

No

→

Go To

13

3

Turn the ignition off.
Disconnect the CMP Sensor harness connector.
Turn the ignition on.
Using a 12-volt test light connected to ground, check the ASD Relay Output circuit in
CMP Sensor harness connector.
Does the test light illuminate brightly?

All

Yes

→

Go To

4

No

→

Repair the ASD Relay Output circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2.

4

Turn the ignition off.
Disconnect the CMP Sensor harness connector.
Turn the ignition on.
Measure the voltage of the CMP Sensor Signal circuit.
Is the voltage above 10.0 volts?

All

Yes

→

Go To

5

No

→

Go To

10

5

Turn the ignition off.
Disconnect the CMP Sensor harness connector.
Turn the ignition on.
Using a 12-volt test light connected to ground, check the CMP Sensor Signal circuit.
Is the test light on?

All

Yes

→

Repair the CMP Sensor Signal circuit for a short to voltage.
Perform ROAD TEST VERIFICATION - VER-2.

No

→

Go To

6

78

DRIVEABILITY - DIESEL

P0340-CMP/CKP POSITION SENSOR CIRCUIT - SIGNAL FREQUENCY
TOO HIGH —

Continued

ProCarManuals.com

Содержание Jeep Grand Cherokee 2002





























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды