manualshive.com logo in svg

DaimlerChrysler Jeep Grand Cherokee 2002, Руководство по обслуживанию

Поделиться
Скачать
DaimlerChrysler Jeep Grand Cherokee 2002 Скачать руководство пользователя страница 238

Symptom:

*CHECKING THE VISCOUS/CABIN HEATER RELAY

POSSIBLE CAUSES

FUSED B+ CIRCUIT OPEN

VISCOUS HEATER RELAY OUTPUT CIRCUIT SHORTED TO VOLTAGE

VISCOUS HEATER RELAY OUTPUT CIRCUIT SHORTED TO GROUND

VISCOUS HEATER RELAY OUTPUT CIRCUIT OPEN

VISCOUS HEATER RELAY

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, actuate the Viscous Heater Relay.
Is the clicking during the actuator test?

All

Yes

→

Test Complete.

No

→

Go To

2

2

NOTE: If the Viscous Heater Relay fuse or fuselink is open, refer to the
system schematics for all circuits that are powered by the Cabin Heater
Relay fuse or fuselink to determine the cause of the blown fuse/fuselink.
Remove the Viscous Heater Relay.
Using a 12-volt test light connected to ground, probe the Fused B+ circuit in the
Viscous Heater Relay connector.
Does the test light illuminate brightly?

All

Yes

→

Go To

3

No

→

Repair the Fused B+ (Fuse/Fuselink) circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2.

3

Turn the ignition off.
Disconnect the Viscous Heater harness connector.
Remove the Viscous Heater Relay.
Turn the ignition on.
Measure the voltage on the Viscous Heater Relay Output circuit.
Is the voltage above 1.0 volt?

All

Yes

→

Repair the Viscous Heater Relay Output circuit for a short to
voltage.
Perform ROAD TEST VERIFICATION - VER-2.

No

→

Go To

4

4

Turn the ignition off.
Disconnect the Viscous Heater harness connector.
Remove the Viscous Heater Relay.
Measure the resistance between ground and the Viscous Heater Relay Output circuit.
Is the resistance above 1000 ohms?

All

Yes

→

Go To

5

No

→

Repair the Viscous Heater Relay Output circuit for a short to
ground. Inspect the fuse or fuselink and replace as necessary.
Perform ROAD TEST VERIFICATION - VER-2.

230

DRIVEABILITY - DIESEL

ProCarManuals.com

Содержание Jeep Grand Cherokee 2002





























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды