manualshive.com logo in svg

DaimlerChrysler Jeep Grand Cherokee 2002, Руководство по обслуживанию

Поделиться
Скачать
DaimlerChrysler Jeep Grand Cherokee 2002 Скачать руководство пользователя страница 46

Symptom:

P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT SIGNAL VOLT-
AGE TOO LOW

When Monitored and Set Condition:

P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO
LOW

When Monitored:

With the ignition on.

Set Condition:

The Engine Coolant Temperature Sensor Signal voltage is below 0.073

volt for more than 3 seconds.

POSSIBLE CAUSES

INTERMITTENT CONDITION

ECT SENSOR

ECT SENSOR SIGNAL CIRCUIT SHORTED TO GROUND

ECT SENSOR SIGNAL AND GROUND CIRCUITS SHORTED TOGETHER

ENGINE CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, monitor the Engine Coolant Temperature (ECT) Sensor voltage.
Is the ECT Sensor voltage below 0.073 volt?

All

Yes

→

Go To

2

No

→

Go To

6

2

Turn the ignition off.
Disconnect the ECT Sensor harness connector.
Turn the ignition on.
With the DRB, read the ECT Sensor voltage.
Is the voltage above 4.0 volts?

All

Yes

→

Replace the ECT Sensor in accordance with the Service Informa-
tion.
Perform ROAD TEST VERIFICATION - VER-2.

No

→

Go To

3

3

Turn the ignition off.
Disconnect the ECM harness connectors.
Disconnect the ECT Sensor harness connector.
Measure the resistance between ground and the ECT Sensor Signal circuit.
Is the resistance above 1000 ohms?

All

Yes

→

Go To

4

No

→

Repair the ECT Sensor Signal circuit for a short to ground.
Perform ROAD TEST VERIFICATION - VER-2.

38

DRIVEABILITY - DIESEL

ProCarManuals.com

Содержание Jeep Grand Cherokee 2002





























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды