DaimlerChrysler Jeep Grand Cherokee 2002 Скачать руководство пользователя страница 72

Страница: 72 / 284

Symptom:

P0243-TURBOCHARGER WASTEGATE SOLENOID CIRCUIT OPEN
CIRCUIT

When Monitored and Set Condition:

P0243-TURBOCHARGER WASTEGATE SOLENOID CIRCUIT OPEN CIRCUIT

When Monitored:

With the ignition on.

Set Condition:

The ECM detects an open or short to ground on the Turbocharger

Wastegate Solenoid Control circuit.

POSSIBLE CAUSES

INTERMITTENT CONDITION

ASD RELAY OUTPUT CIRCUIT OPEN

TURBOCHARGER WASTEGATE SOLENOID CONTROL CIRCUIT SHORTED TO GROUND

TURBOCHARGER WASTEGATE SOLENOID CONTROL CKT OPEN

TURBOCHARGER WASTEGATE SOLENOID

ENGINE CONTROL MODULE

TEST

ACTION

APPLICABILITY

Turn the ignition on.
With the DRB, erase ECM DTCs.
Test drive the vehicle.
Monitor the DRB for ECM DTCs.
Did this DTC set again?

All

Yes

→

Go To

→

Go To

Turn the ignition off.
Disconnect the Turbocharger Wastegate Solenoid harness connector.
Turn the ignition on.
Using a 12-volt test light connected to ground, check the ASD Relay Output circuit.
Does the test light illuminate brightly?

All

Yes

→

Go To

→

Repair the ASD Relay Output circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2.

DRIVEABILITY - DIESEL

ProCarManuals.com

Содержание Jeep Grand Cherokee 2002





























































































































































































































































































Результаты поиска

Содержание Jeep Grand Cherokee 2002

Отзывы:

Бренды по названию

Популярные бренды

DaimlerChrysler Jeep Grand Cherokee 2002, Руководство по обслуживанию

Результаты поиска

Содержание Jeep Grand Cherokee 2002

Отзывы:

Бренды по названию

Популярные бренды