manualshive.com logo in svg

DaimlerChrysler Jeep Grand Cherokee 2002, Руководство по обслуживанию

Поделиться
Скачать
DaimlerChrysler Jeep Grand Cherokee 2002 Скачать руководство пользователя страница 108

TEST

ACTION

APPLICABILITY

5

Turn the ignition off.
Disconnect the CAB harness connectors.
Disconnect the ECM harness connectors.
Remove the ASD Relay from the PDC.
Connect a jumper wire between cavity 30 and cavity 87 of the ASD Relay connector.
Turn the ignition on.
Measure the voltage on the Vehicle Speed Signal circuit.
Is the voltage above 1.0 volt?

All

Yes

→

Repair the Vehicle Speed Signal circuit for a short to voltage.
Perform ROAD TEST VERIFICATION - VER-2.

No

→

Replace and program the Engine Control Module in accordance
with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

6

Turn the ignition off.
Disconnect the CAB harness connectors.
Turn the ignition on.
Connect one end of a jumper wire to the Vehicle Speed Signal circuit.
With the DRB, select, isolate and observe the Vehicle Speed status while tapping the
other end of the jumper wire to ground.
Does the DRB display a vehicle speed change while tapping the jumper wire to
ground?

All

Yes

→

Replace the Controller Antilock Brake Module in accordance with
the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

No

→

Replace and program the Engine Control Module in accordance
with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

7

Turn the ignition off.
Disconnect the CAB harness connectors.
Disconnect the ECM harness connectors.
Measure the resistance between ground and the Vehicle Speed Signal circuit.
Is the resistance above 100 kohms?

All

Yes

→

Go To

8

No

→

Repair the Vehicle Speed Signal circuit for a short to ground.
Perform ROAD TEST VERIFICATION - VER-2.

8

Turn the ignition off.
Disconnect the CAB harness connectors.
Disconnect the ECM harness connectors.
Measure the resistance of the Vehicle Speed Signal circuit.
Is the resistance below 5.0 ohms?

All

Yes

→

Go To

9

No

→

Repair the Vehicle Speed Signal circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2.

9

If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Engine Control Module in accordance
with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

100

DRIVEABILITY - DIESEL

P0500-VEHICLE SPEED SENSOR FREQUENCY TOO HIGH —

Continued

ProCarManuals.com

Содержание Jeep Grand Cherokee 2002





























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды