Daikin VRV Aurora RXLQ-TATJU Series, Руководство по обслуживанию

Страница: 235 / 442

SiUS341802EC Troubleshooting by Error Code
Part 6 Service Diagnosis 228
U2 - 01 Shortage of inverter 1 power supply voltage (Master) Make a diagnosis of the relevant unit based on the
following.
Shortage of power supply voltage
If the other units detect shortage of power supply voltage,
power supply voltage during operation may be unstable.
Check the power supply condition.
If a particular unit detects the error, operation of 52C may
be defective. Follow the U2 flowchart.
Open phase of power supply
The wiring between power supply and inverter PCB may be
disconnected. Check that power supply is connected to
terminal block, terminal block is connected to PCB without
broken wire or disconnection, and reactor wiring is
secured. If no abnormality is found, follow the U2 flowchart.
Defective capacitor in main circuit
P-N on the inverter PCB (electrolytic capacitor, power
module) may be damaged and short circuited. Operation of
current limiting relay may be defective or the wiring
between the reactor and PCB may be disconnected.
Measure the resistance between P-N on the inverter PCB
and check for short circuit. If no abnormality is found, follow
the U2 flowchart.
U2 - 02 Open phase of inverter 1 power supply (Master)
U2 - 03 Defective capacitor in inverter 1 main circuit (Master)
U2 - 08 Shortage of inverter 1 power supply voltage (Slave 1)
U2 - 09 Open phase of inverter 1 power supply (Slave 1)
U2 - 10 Defective capacitor in inverter 1 main circuit (Slave 1)
U2 - 11 Shortage of inverter 1 power supply voltage (Slave 2)
U2 - 12 Open phase of inverter 1 power supply (Slave 2)
U2 - 13 Defective capacitor in inverter 1 main circuit (Slave 2)
U2 - 36
Fan motor 1 undervoltage (Master)
U2 - 37
Fan motor 2 undervoltage (Master)
U2 - 38
Fan motor 1 undervoltage (Slave 1)
U2 - 39
Fan motor 2 undervoltage (Slave 1)
U2 - 40
Fan motor 1 undervoltage (Slave 2)
U2 - 41
Fan motor 2 undervoltage (Slave 2)
U3 - 02 Initial installation warning Refer to the U3 flowchart and make a diagnosis of the
relevant unit based on the Error code shown to the left.
U3 - 03 Test operation not conducted
U3 - 04 Abnormal end of test operation
U3 - 05
Premature end of test operation during initial transmission
error
U3 - 06
Premature end of test operation during normal
transmission error
U3 - 07
Premature end of test operation due to transmission error
of either unit
U3 - 08
Premature end of test operation due to transmission error
of all units
U4 - 01 Transmission error between indoor units and outdoor units Refer to the U4 flowchart and make a diagnosis of the
relevant unit based on the Error code shown to the left.
U4 - 03 Transmission error between indoor unit and system
U7 - 01
Error when external control adaptor for outdoor unit is
installed
Refer to the U7 flowchart and make a diagnosis of the
relevant unit based on the Error code shown to the left.
U7 - 02
Warning when external control adaptor for outdoor unit is
installed
U7 - 03 Transmission error between master and slave 1 units
U7 - 04 Transmission error between master and slave 2 units
U7 - 05 Multi system error
U7 - 06 Error in address settings of slave 1 and 2
U7 - 07
Connection of four or more outdoor units in the same
system
U7 - 11 Error in indoor unit connection capacity for test operation
U9 - 01
Other indoor units abnormality Refer to the
U9
flowchart and make a diagnosis of the
relevant unit based on the Error code shown to the left.
UA - 13
Refrigerant type error The type of refrigerant used for the indoor unit is different
from that used for the outdoor unit.
UA - 15
Not applicable for self-cleaning decoration panel
[when the self-cleaning decoration panel is mounted]
An outdoor unit is not applicable for the self-cleaning
decoration panel is connected.
Error code
Troubleshooting
Error Description Diagnosis