Daewoo DAPD17REQ-EC, Руководство пользователя

Страница: 37 / 50

• Take off the red cap of battery positive.
• Use the multi-meter to check whether the voltage of battery is over 12.6V, charge the battery if the
voltage is lower than this.
• Loose the positive battery clip. Put it onto the positive terminal fully and adjust the direction.
• Fasten the nut on the battery clip.
• Cover it with the red battery clip rubber.
Servicing of battery is to be performed or supervised by personnel knowledgeable of
battery and the required precautions. Keep unauthorized personnel away from battery.
When replacing batteries, use the same number and the following type batteries: 12V, Lead-acid
battery.
CAUTION
CAUTION
– Do not open or mutilate the battery. Released electrolyte has been known to be harmful
to the skin and eyes and to be toxic.
CAUTION
– A battery presents a risk of electrical shock and high short circuit current. The following
precautions are to be observed when working on batteries:
1. Remove watches, rings, or other metal objects,
2. Use tools with insulated handles,
3. Wear rubber gloves and boots,
4. Do not lay tools or metal parts on top of batteries,
5. Disconnect.
7. Grounding
Ground the gas generator. Connect the grounding strap to the gas generator ground terminal.
6. STARTUP
1. Turn on the emergency stop switch.
2. Turn on the power switch 2.
3. Turn on the fuel switch 3.
4. After 10s turn on the fuel switch, press the manul 5 on control panel.
5. Press 6, unit enter into start.
6. Press 7 or 8, observe the frequency, voltage , speed and the 12V working voltage as well as the
operation time.
7. After the unit started then can be automatically generation( match with ATS enter into automatical
mode).
• Take off the red cap of battery positive.
• Use the multi-meter to check whether the voltage of battery is over 12.6V, charge the battery if the
voltage is lower than this.
• Loose the positive battery clip. Put it onto the positive terminal fully and adjust the direction.
• Fasten the nut on the battery clip.
• Cover it with the red battery clip rubber.
Servicing of battery is to be performed or supervised by personnel knowledgeable of
battery and the required precautions. Keep unauthorized personnel away from battery.
When replacing batteries, use the same number and the following type batteries: 12V, Lead-acid
battery.
CAUTION
CAUTION
– Do not open or mutilate the battery. Released electrolyte has been known to be harmful
to the skin and eyes and to be toxic.
CAUTION
– A battery presents a risk of electrical shock and high short circuit current. The following
precautions are to be observed when working on batteries:
1. Remove watches, rings, or other metal objects,
2. Use tools with insulated handles,
3. Wear rubber gloves and boots,
4. Do not lay tools or metal parts on top of batteries,
5. Disconnect.
7. Grounding
Ground the gas generator. Connect the grounding strap to the gas generator ground terminal.
6. STARTUP
1. Turn on the emergency stop switch.
2. Turn on the power switch 2.
3. Turn on the fuel switch 3.
4. After 10s turn on the fuel switch, press the manul 5 on control panel.
5. Press 6, unit enter into start.
6. Press 7 or 8, observe the frequency, voltage , speed and the 12V working voltage as well as the
operation time.
7. After the unit started then can be automatically generation( match with ATS enter into automatical
mode).
• Take off the red cap of battery positive.
• Use the multi-meter to check whether the voltage of battery is over 12.6V, charge the battery if the
voltage is lower than this.
• Loose the positive battery clip. Put it onto the positive terminal fully and adjust the direction.
• Fasten the nut on the battery clip.
• Cover it with the red battery clip rubber.
Servicing of battery is to be performed or supervised by personnel knowledgeable of
battery and the required precautions. Keep unauthorized personnel away from battery.
When replacing batteries, use the same number and the following type batteries: 12V, Lead-acid
battery.
CAUTION
CAUTION
– Do not open or mutilate the battery. Released electrolyte has been known to be harmful
to the skin and eyes and to be toxic.
CAUTION
– A battery presents a risk of electrical shock and high short circuit current. The following
precautions are to be observed when working on batteries:
1. Remove watches, rings, or other metal objects,
2. Use tools with insulated handles,
3. Wear rubber gloves and boots,
4. Do not lay tools or metal parts on top of batteries,
5. Disconnect.
7. Grounding
Ground the gas generator. Connect the grounding strap to the gas generator ground terminal.
6. STARTUP
1. Turn on the emergency stop switch.
2. Turn on the power switch 2.
3. Turn on the fuel switch 3.
4. After 10s turn on the fuel switch, press the manul 5 on control panel.
5. Press 6, unit enter into start.
6. Press 7 or 8, observe the frequency, voltage , speed and the 12V working voltage as well as the
operation time.
7. After the unit started then can be automatically generation( match with ATS enter into automatical
mode).
Connect battery positive (+) and negative (-) to wire positive and negative side, connect negative (-)
• Take off the red cap of battery positive.
• Use the multi-meter to check whether the voltage of battery is over 12.6V, charge the battery if the
voltage is lower than this.
• Loose the positive battery clip. Put it onto the positive terminal fully and adjust the direction.
• Fasten the nut on the battery clip.
• Cover it with the red battery clip rubber.
Servicing of battery is to be performed or supervised by personnel knowledgeable of
battery and the required precautions. Keep unauthorized personnel away from battery.
When replacing batteries, use the same number and the following type batteries: 12V, Lead-acid
battery.
CAUTION
CAUTION
– Do not open or mutilate the battery. Released electrolyte has been known to be harmful
to the skin and eyes and to be toxic.
CAUTION
– A battery presents a risk of electrical shock and high short circuit current. The following
precautions are to be observed when working on batteries:
1. Remove watches, rings, or other metal objects,
2. Use tools with insulated handles,
3. Wear rubber gloves and boots,
4. Do not lay tools or metal parts on top of batteries,
5. Disconnect.
7. Grounding
Ground the gas generator. Connect the grounding strap to the gas generator ground terminal.
6. STARTUP
1. Turn on the emergency stop switch.
2. Turn on the power switch 2.
3. Turn on the fuel switch 3.
4. After 10s turn on the fuel switch, press the manul 5 on control panel.
5. Press 6, unit enter into start.
6. Press 7 or 8, observe the frequency, voltage , speed and the 12V working voltage as well as the
operation time.
7. After the unit started then can be automatically generation( match with ATS enter into automatical
mode).
Connect battery positive (+) and negative (-) to wire positive and negative side, connect negative (-)
• Take off the red cap of battery positive.
• Use the multi-meter to check whether the voltage of battery is over 12.6V, charge the battery if the
voltage is lower than this.
• Loose the positive battery clip. Put it onto the positive terminal fully and adjust the direction.
• Fasten the nut on the battery clip.
• Cover it with the red battery clip rubber.
Servicing of battery is to be performed or supervised by personnel knowledgeable of
battery and the required precautions. Keep unauthorized personnel away from battery.
When replacing batteries, use the same number and the following type batteries: 12V, Lead-acid
battery.
CAUTION
CAUTION
– Do not open or mutilate the battery. Released electrolyte has been known to be harmful
to the skin and eyes and to be toxic.
CAUTION
– A battery presents a risk of electrical shock and high short circuit current. The following
precautions are to be observed when working on batteries:
1. Remove watches, rings, or other metal objects,
2. Use tools with insulated handles,
3. Wear rubber gloves and boots,
4. Do not lay tools or metal parts on top of batteries,
5. Disconnect.
7. Grounding
Ground the gas generator. Connect the grounding strap to the gas generator ground terminal.
6. STARTUP
1. Turn on the emergency stop switch.
2. Turn on the power switch 2.
3. Turn on the fuel switch 3.
4. After 10s turn on the fuel switch, press the manul 5 on control panel.
5. Press 6, unit enter into start.
6. Press 7 or 8, observe the frequency, voltage , speed and the 12V working voltage as well as the
operation time.
7. After the unit started then can be automatically generation( match with ATS enter into automatical
mode).
Connect battery positive (+) and negative (-) to wire positive and negative side, connect negative (-)
lead last when connecting the battery. The gas generator will not start and circuit board damage
• Take off the red cap of battery positive.
• Use the multi-meter to check whether the voltage of battery is over 12.6V, charge the battery if the
voltage is lower than this.
• Loose the positive battery clip. Put it onto the positive terminal fully and adjust the direction.
• Fasten the nut on the battery clip.
• Cover it with the red battery clip rubber.
Servicing of battery is to be performed or supervised by personnel knowledgeable of
battery and the required precautions. Keep unauthorized personnel away from battery.
When replacing batteries, use the same number and the following type batteries: 12V, Lead-acid
battery.
CAUTION
CAUTION
– Do not open or mutilate the battery. Released electrolyte has been known to be harmful
to the skin and eyes and to be toxic.
CAUTION
– A battery presents a risk of electrical shock and high short circuit current. The following
precautions are to be observed when working on batteries:
1. Remove watches, rings, or other metal objects,
2. Use tools with insulated handles,
3. Wear rubber gloves and boots,
4. Do not lay tools or metal parts on top of batteries,
5. Disconnect.
7. Grounding
Ground the gas generator. Connect the grounding strap to the gas generator ground terminal.
6. STARTUP
1. Turn on the emergency stop switch.
2. Turn on the power switch 2.
3. Turn on the fuel switch 3.
4. After 10s turn on the fuel switch, press the manul 5 on control panel.
5. Press 6, unit enter into start.
6. Press 7 or 8, observe the frequency, voltage , speed and the 12V working voltage as well as the
operation time.
7. After the unit started then can be automatically generation( match with ATS enter into automatical
mode).
13
،ارﺟا زا لﺑﻗ ﻣز ﮫﺑ لﺎﺻﺗا زا ﯾ وﺷ نﺋﻣطﻣ ن ﯾ د .
ﺎھ رﺎﺑ ﺎﺑ ﮫﺧﺎﺷود ی ﻧﮐ دراو ار فﻠﺗﺧﻣ ﯾ د
ﯾ زﺎﻓ ﮏ
زﺎﻓ ﮫﺳ
ﻠﺻا نزﺧﻣ ﯽ ﺎﺑ ر
ا ﻣ رﮔ ﯽ ھاوﺧ ﯾ لﺧاد زا د ATS ا ﺳ ﺗﻔ ﺎد ه ﮐﻧ ﯾ رﮭﺷ قرﺑ ،د ی ﻧﮐ لﺻو دﺣاو ﮫﺑ ار ﯾ د . ﺟورﺧ ﯽ ﺎﺑ زوزﮔا ﯾ ﺗﮭﺟ نﺎﻣھ د ﯽ ﻣ دﺎﺑ ﮫﮐ دﺷﺎﺑ ﯽ دزو .