ENGLISH
92
GB
9
Reset of resettable blocks NO
10
Low pressure signal input NO,
automatic and manual reset
F4
11
Low pressure signal input NC,
automatic and manual reset
F4
12
Low pressure input NO only manual
reset
F4
13
Low pressure input NC only manual
reset
F4
7.6.15.1 - Disabling the functions associated with the input
7.6.15.1 - Disabling the functions associated with the input
Setting 0 as the configuration value of an input, each function associated
Setting 0 as the configuration value of an input, each function associated
with the input will be disabled irrespective of the signal present on the input
with the input will be disabled irrespective of the signal present on the input
terminals.
terminals.
7.6.15.2 - Setting external float function
7.6.15.2 - Setting external float function
The external float can be connected to any input, for the electrical connec
-
The external float can be connected to any input, for the electrical connec
-
tions refer to the control unit manual.
tions refer to the control unit manual.
The float function is obtained, setting one of the values in Table 16 on the
The float function is obtained, setting one of the values in Table 16 on the
parameter Ix, for the input to which the float has been connected.
parameter Ix, for the input to which the float has been connected.
The activation of the external float function generates the block of the sys
-
The activation of the external float function generates the block of the sys
-
tem. The function is conceived for connecting the input to a signal arriving
tem. The function is conceived for connecting the input to a signal arriving
from a float which indicates lack of water.
from a float which indicates lack of water.
When this function is active the float switch symbol is shown on the STA
-
When this function is active the float switch symbol is shown on the STA
-
TUS line of the main page.
TUS line of the main page.
For the system to block and give the error signal F1, the input must be
For the system to block and give the error signal F1, the input must be
activated for at least 1 sec.
activated for at least 1 sec.
When it is in error condition F1, the input must have been deactivated for
When it is in error condition F1, the input must have been deactivated for
at least 30 sec before the system can be unblocked. The behaviour of the
at least 30 sec before the system can be unblocked. The behaviour of the
function is summed up in Table 15.
function is summed up in Table 15.
When several float functions are configured at the same time on different
When several float functions are configured at the same time on different
Table 14: Configurations of the digital inputs
inputs, the system will indicate F1 when at least one function is activated
inputs, the system will indicate F1 when at least one function is activated
and will remove the alarm when none is activated.
and will remove the alarm when none is activated.
Behaviour of the external float function depending on INx and on the input
Value of
Parameter
Ix
Input configu
-
ration
Input status
Operation
Shown on
display
1
Active with high
signal on input
(NO)
Absent
Normal
None
Present
System block
for water lack by
external float
F1
2
Active with low
signal on input
(NC)
Absent
System block
for water lack by
external float
F1
Present
Normal
None
7.6.15.3 - Setting auxiliary setpoint input function
7.6.15.3 - Setting auxiliary setpoint input function
The signal that enables an auxiliary setpoint can be supplied on any of the
The signal that enables an auxiliary setpoint can be supplied on any of the
4 inputs (for the electrical connections, refer to the control unit manual).
4 inputs (for the electrical connections, refer to the control unit manual).
The auxiliary setpoint is obtained by setting the Ix parameter relating to the
The auxiliary setpoint is obtained by setting the Ix parameter relating to the
input on which the connection has been made, in accordance with Table
input on which the connection has been made, in accordance with Table
17. Example:. to use Paux 2, set I2 on 3 or 4 and use input 2 on the control
17. Example:. to use Paux 2, set I2 on 3 or 4 and use input 2 on the control
unit; in this condition, if input 2 is energized, pressure Paux 2 will be pro
-
unit; in this condition, if input 2 is energized, pressure Paux 2 will be pro
-
duced and the display will show P2.
duced and the display will show P2.
The auxiliary setpoint function modifies the system setpoint from pressure
The auxiliary setpoint function modifies the system setpoint from pressure
SP (see par. 7.3 – Setpoint Menu ) to pressure Pi, where is represents the
SP (see par. 7.3 – Setpoint Menu ) to pressure Pi, where is represents the
input used. In this way, as well as SP, four other pressures are available,
input used. In this way, as well as SP, four other pressures are available,
P1, P2, P3, P4.
P1, P2, P3, P4.
When this function is active the symbol Pi is shown on the main page.
When this function is active the symbol Pi is shown on the main page.
For the system to work with the auxiliary setpoint, the input must be active
For the system to work with the auxiliary setpoint, the input must be active
for at least 1 sec.
for at least 1 sec.
Table 15: External float function
Содержание e.sybox Series
Страница 3: ......
