xStack DGS-3400 Series Layer 2 Gigabit Ethernet Managed Switch
IGMP Multicast
Router Only
This field specifies that the Switch should only forward all multicast traffic to a multicast-enabled
router, if enabled. Otherwise, the Switch will forward all multicast traffic to any IP router. The
default is
Disabled
.
MLD Snooping
To enable system-wide MLD Snooping capability select
Enabled
. MLD snooping is
Disabled
by
default. Enabling MLD snooping allows you to specify use of a multicast router only (see below).
To configure MLD Snooping for individual VLANs, use the MLD Snooping window under the
MLD Snooping folder.
MLD Multicast
Router Only
This field specifies that the Switch should only forward all multicast traffic to a multicast-enabled
router, if enabled. Otherwise, the Switch will forward all multicast traffic to any IP router. The
default is
Disabled
.
GVRP Status
Use this pull-down menu to enable or disable GVRP on the Switch.
Telnet Status
Telnet configuration is
Enabled
by default. If you do not want to allow configuration of the
system through Telnet choose
Disabled
.
Telnet TCP Port
Number (1-65535)
The TCP port number used for Telnet management of the Switch. The "well-known" TCP port for
the Telnet protocol is
23
.
Web Status
Web-based management is
Enabled
by default. If you choose to disable this by selecting
Disabled
, you will lose the ability to configure the system through the web interface as soon as
these settings are applied.
Web TCP Port
Number (1-65535)
The TCP port number used for Web-based management of the Switch. The "well-known" TCP
port for the Telnet protocol is
80
.
RMON Status
Remote monitoring (RMON) of the Switch is
Enabled
or
Disabled
here.
Link Aggregation
Algorithm
The algorithm that the Switch uses to balance the load across the ports that make up the port
trunk group is defined by this definition. Choose
MAC Source
,
MAC Destination
,
MAC Src &
Dest
,
IP Source, IP Destination
or
IP Src & Dest
(See the Link Aggregation section of this
manual).
Switch 802.1X
MAC Address may enable by port or the Switch’s 802.1X function; the default is
Disabled
. This
field must be enabled to view and configure certain windows for 802.1X. More information
regarding 802.1X, its functions and implementation can be found later in this section, under the
Port Access Entity folder.
Port-Based 802.1X specifies that ports configured for 802.1X are initialized based on the port
number only and are subject to any authorization parameters configured.
MAC-based Authorization specifies that ports configured for 802.1X are initialized based on the
port number and the MAC address of the computer being authorized and are then subject to any
authorization parameters configured.
Auth Protocol
The user may use the pull-down menu to choose between
RADIUS EAP
and
Local
for the
802.1X authentication protocol on the Switch. The default setting is
RADIUS EAP
.
HOL Prevention
If this option is enabled it prevents the forwarding of data to a port that is blocked. Traffic that
would normally be sent to the buffer memory of the Switch’s TX queue is dropped so that
memory usage is conserved and performance across all ports remains high.
Jumbo Frame
This field will enable or disable the Jumbo Frame function on the Switch. The default is
Disabled. Max. Jumbo frame size = 9216 bytes if this is enabled.
Syslog State
The user may globally enable or disable the Syslog function here by using the pull-down menu.
The default is
Disabled
.
ARP Aging time
The user may set the ARP Aging Time here by entering a time between 0 and 65535 minutes.
The default setting is 20 minutes.
Click
Apply
to implement changes made.
32
Содержание xStack DGS-3426P
Страница 307: ...software updates D Link D Link D Link 210 86 11 114 210 86 53 172 09 00 17 00 e mail support dlink gr D Link Internet...
Страница 310: ...D Link D Link D Link D Link 495 744 00 99 http www dlink ru e mail support dlink ru...
Страница 316: ...International Offices...
Страница 318: ......