manualshive.com logo in svg

D-Link DXS-3326GSR - xStack Switch - Stackable, Руководство пользователя

D-Link DXS-3326GSR - xStack Switch - Stackable - это высококачественный коммутатор с возможностью стекирования. Вы можете бесплатно скачать Руководство по эксплуатации с нашего сайта. Посетите manualshive.com для загрузки этого руководства и получите дополнительную информацию о продукте.

Поделиться
Скачать
background image

DXS-3326GSR Gigabit Layer 3 Switch 

The following fields can then be set: 

Parameter                    Description 

Unit 

Choose the desired Unit. 

VID (VLAN ID) 

Allows the entry of a VLAN ID in the Add dialog box, or displays the VLAN ID of an 
existing VLAN in the Modify dialog box. VLANs can be identified by either the VID or the 
VLAN name. 

VLAN Name 

Allows the entry of a name for the new VLAN in the Add dialog box, or for editing the 
VLAN name in the Modify dialog box. 

Advertisement 

Enabling this function will allow the Switch to send out GVRP packets to outside 
sources, notifying that they may join the existing VLAN. 

Protocol ID 

The following parameters allow for the creation of protocol-based VLANs. The switch 
supports 15 pre-configured protocol-based VLANs plus one user-defined protocol based 
VLAN where the administrator may configure the settings for the appropriate protocol 
and forwarding of packets (16 total). Selecting a specific protocol will indicate which 
protocol will be utilized in determining the VLAN ownership of a tagged packet. Pre-set 
protocol-based VLANs on the switch include: 

port

 – Using this parameter will allow the creation of a normal 802.1Q VLAN on the 

Switch. 

ip

 – Using this parameter will instruct the switch to forward packets to this VLAN if the 

tag in the packet header is concurrent with this protocol. This packet header information 
is based on the Ethernet protocol. 

rarp - 

Using this parameter will instruct the switch to forward packets to this VLAN if the 

tag in the packet header is concurrent with this protocol. This packet header information 
is defined by the Reverse Address Resolution (RARP) Protocol. 

ipx802dot3

 - Using this parameter will instruct the switch to forward packets to this 

VLAN if the tag in the packet header is concurrent with this protocol. This packet header 
information is defined by Novell NetWare 802.3 (IPX - Internet Packet Exchange). 

ipx802dot2 - 

Using this parameter will instruct the switch to forward packets to this 

VLAN if the tag in the packet header is concurrent with this protocol. This packet header 
information is defined by Novell NetWare 802.2 (IPX - Internet Packet Exchange). 

ipxSnap 

- Using this parameter will instruct the switch to forward packets to this VLAN if 

the tag in the packet header is concurrent with this protocol. This packet header 
information is defined by Novell and the Sub Network Access Protocol (SNAP). 

ipxEthernet2 - 

Using this parameter will instruct the switch to forward packets to this 

VLAN if the tag in the packet header is concurrent with this protocol. This packet header 
information is defined by the Ethernet Protocol. 

appleTalk 

- Using this parameter will instruct the switch to forward packets to this VLAN 

if the tag in the packet header is concurrent with this protocol. This packet header 
information is defined by the AppleTalk protocol. 

decLAT - 

Using this parameter will instruct the switch to forward packets to this VLAN if 

the tag in the packet header is concurrent with this protocol. This packet header 
information is defined by the Digital Equipment Corporation (DEC) Local Area Transport 
(LAT) protocol. 

decOther - 

Using this parameter will instruct the switch to forward packets to this VLAN 

if the tag in the packet header is concurrent with this protocol. This packet header 
information is defined by the Digital Equipment Corporation (DEC) Protocol.

 

sna802dot2 - 

Using this parameter will instruct the switch to forward packets to this 

VLAN if the tag in the packet header is concurrent with this protocol. This packet header 

72 

Содержание DXS-3326GSR - xStack Switch - Stackable































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DXS-3326GSR - xStack Switch - Stackable

D-Link Verizon DSL-2750B Connection Instructions preview
Verizon DSL-2750B
Бренд: D-Link Страницы: 2
D-Link DVA-2800 Quick Start Manual preview
DVA-2800
Бренд: D-Link Страницы: 4
C&H Technologies EM405-8 Manual preview
EM405-8
Бренд: C&H Technologies Страницы: 46
IBM 11a Quick Start Manual preview
11a
Бренд: IBM Страницы: 32
ICP DAS USA ET-7000 series Quick Start Manual preview
ET-7000 series
Бренд: ICP DAS USA Страницы: 14
ICP DAS USA I-2533 User Manual preview
I-2533
Бренд: ICP DAS USA Страницы: 25
ICP DAS USA ET-2200 Series Manual preview
ET-2200 Series
Бренд: ICP DAS USA Страницы: 15
ICP ZT-2550 Quick Start Manual preview
ZT-2550
Бренд: ICP Страницы: 14
Danfoss TFX Installation And Operation Manual preview
TFX
Бренд: Danfoss Страницы: 61
D-Link G416 User Manual preview
G416
Бренд: D-Link Страницы: 176
ZyXEL Communications ADSL/ADSL2/ADSL2+ Router 660R-6xC Series User Manual preview
ADSL/ADSL2/ADSL2+ Router 660R-6xC Series
Бренд: ZyXEL Communications Страницы: 282
APARIAN DH485 Quick Start Manuals preview
DH485
Бренд: APARIAN Страницы: 2
Surveon EonServ 5000 Series User Manual preview
EonServ 5000 Series
Бренд: Surveon Страницы: 33
TRENDnet TE100-S16 - 10/100Mbps Ethernet Switch User Manual preview
TE100-S16 - 10/100Mbps Ethernet Switch
Бренд: TRENDnet Страницы: 15
TP-Link TL-SG2424P User Manual preview
TL-SG2424P
Бренд: TP-Link Страницы: 176
Nexxt NOVA300 AML02304U1 User Manual preview
NOVA300 AML02304U1
Бренд: Nexxt Страницы: 75
Paradyne FrameSaver DSL 9788 Router Installation Instructions Manual preview
FrameSaver DSL 9788 Router
Бренд: Paradyne Страницы: 28
H3C AR 46-80 Installation Manual preview
AR 46-80
Бренд: H3C Страницы: 103

Бренды по названию

Популярные бренды

Загрузить еще бренды