manualshive.com logo in svg

D-Link DXS-3326GSR - xStack Switch - Stackable, Руководство пользователя, Страница: 191 / 286

Поделиться
Скачать
D-Link DXS-3326GSR - xStack Switch - Stackable Скачать руководство пользователя страница 191

DXS-3326GSR Gigabit Layer 3 Switch 

Parameter                      Description 

IP Address 

The IP address of the remote server host the user wishes to add. 

Protocol 

The protocol used by the server host. The user may choose one of the following: 

• 

• 

• 

• 

TACACS

 - Enter this parameter if the server host utilizes the TACACS 

protocol. 

XTACACS

 - Enter this parameter if the server host utilizes the XTACACS 

protocol. 

 - Enter this parameter if the server host utilizes the  

protocol. 

RADIUS

 - Enter this parameter if the server host utilizes the RADIUS 

protocol. 

Port (1-65535) 

Enter a number between 

1

 and 

65535

 to define the virtual port number of the 

authentication protocol on a server host. The default port number is 

49

 for 

TACACS/XTACACS/ servers and 

1813

 for RADIUS servers but the user 

may set a unique port number for higher security. 

Timeout (1-255) 

Enter the time in seconds the Switch will wait for the server host to reply to an 
authentication request. The default value is 

5

 seconds. 

Retransmit (1-255) 

Enter the value in the retransmit field to change how many times the device will 
resend an authentication request when the TACACS server does not respond. 

Key 

Authentication key to be shared with a configured  or RADIUS servers only. 
Specify an alphanumeric string up to 254 characters. 

Click 

Apply

 to add the server host. 

 

NOTE:

 More than one authentication protocol can be run on the same 

physical server host but, remember that TACACS/XTACACS/ 
are separate entities and are not compatible with each other 

Login Method Lists 

This command will configure a user-defined or default Login Method List of authentication techniques for users logging 
on to the Switch. The sequence of techniques implemented in this command will affect the authentication result. For 
example, if a user enters a sequence of techniques, for example TACACS - XTACACS- local, the Switch will send an 
authentication request to the first TACACS host in the server group. If no response comes from the server host, the Switch 
will send an authentication request to the second TACACS host in the server group and so on, until the list is exhausted. At 
that point, the Switch will restart the same sequence with the following protocol listed, XTACACS. If no authentication 
takes place using the XTACACS list, the local account database set in the Switch is used to authenticate the user. When the 
local method is used, the privilege level will be dependant on the local account privilege configured on the Switch. 

Successful login using any of these techniques will give the user a "User" privilege only. If the user wishes to upgrade his 
or her status to the administrator level, the user must use the 

Enable Admin 

window, in which the user must enter a 

previously configured password, set by the administrator. (See the Enable Admin part of this section for more detailed 
information concerning the Enable Admin command.) 

To view the following window click 

Security Management > Access Authentication Control > Login Method Lists

: 

178 

Содержание DXS-3326GSR - xStack Switch - Stackable































































































































































































































































































Отзывы:

Нет отзывов