manualshive.com logo in svg

D-Link DXS-3326GSR - xStack Switch - Stackable, Руководство пользователя

Поделиться
Скачать
D-Link DXS-3326GSR - xStack Switch - Stackable Скачать руководство пользователя страница 138

DXS-3326GSR Gigabit Layer 3 Switch 

the VLAN entered above.

 Secondary

 interfaces can only be configured if a 

primary 

interface is first configured. 

State 

<

Disabled

>

 

This field may be altered between 

Enabled 

and 

Disabled

 using the pull-down menu. 

This entry determines whether the interface will be active or not. 

Link Status 

<

Link 

UP

>

 

This read-only field states the current status of the IP Interface on the Switch. 

Link Up 

denotes that the IP interface is up and running on the Switch. 

Link Down

 will denote 

that the IP interface is not currently set and/or enabled on the Switch. 

Click 

Apply

 to implement changes made. 

MD5 Key Table Configuration 

The 

MD5 Key Setting 

window allows the entry of a 16-character Message Digest 

−

 version 5 (MD5) key that can be used 

to authenticate every packet exchanged between OSPF routers. It is used as a security mechanism to limit the exchange of 
network topology information to the OSPF routing domain. 

MD5 Keys created here can be used in the 

OSPF Interface Configuration 

window below. 

To

 

configure an MD5 Key, click the 

MD5 Key Table Configuration 

link to open the following window: 

 

Figure 7- 5. MD5 Key Setting window 

The following fields can be set: 

Parameter 

           Description 

Key ID (1-255) 

A number from 

1

 to 

255

 used to identify the MD5 Key. 

Key 

A alphanumeric string of between 

1

 and 

16

 case-sensitive characters used to generate 

the Message Digest which is in turn, used to authenticate OSPF packets within the 
OSPF routing domain. 

Click 

Apply

 to enter the new Key ID settings. To delete a Key ID entry, click the corresponding 

 under the Delete 

heading. 

Route Redistribution Settings 

Route redistribution allows routers on the network, which are running different routing protocols to exchange routing 
information. This is accomplished by comparing the routes stored in the various routers routing tables and assigning 
appropriate metrics. This information is then exchanged among the various routers according to the individual routers 
current routing protocol. The Switch can redistribute routing information between the OSPF and RIP routing protocols to 
all routers on the network that are running OSPF or RIP. Routing information entered into the Static Routing Table on the 
local DXS-3326GSR switch is also redistributed. 

125 

Содержание DXS-3326GSR - xStack Switch - Stackable































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды