D-Link DXS-3326GSR - xStack Switch - Stackable страница 243 Скачать руководство пользователя | Manualshive

Страница: 243 / 286

background image

DXS-3326GSR Gigabit Layer 3 Switch

AuthServerAddr

The (conceptual) table listing the RADIUS authentication servers with which the client
shares a secret.

ServerPortNumber

The UDP port the client is using to send requests to this server.

RoundTripTime

The time interval (in hundredths of a second) between the most recent Access-
Reply/Access-Challenge and the Access-Request that matched it from this RADIUS
authentication server.

AccessRequests

The number of RADIUS Access-Request packets sent to this server. This does not
include retransmissions.

AccessRetrans

The number of RADIUS Access-Request packets retransmitted to this RADIUS
authentication server.

AccessAccepts

The number of RADIUS Access-Accept packets (valid or invalid) received from this
server.

AccessRejects

The number of RADIUS Access-Reject packets (valid or invalid) received from this
server.

AccessChallenges

The number of RADIUS Access-Challenge packets (valid or invalid) received from this
server.

AccessResponses

The number of malformed RADIUS Access-Response packets received from this
server. Malformed packets include packets with an invalid length. Bad authenticators
or Signature attributes or known types are not included as malformed access
responses.

BadAuthenticators

The number of RADIUS Access-Response packets containing invalid authenticators
or Signature attributes received from this server.

PendingRequests

The number of RADIUS Access-Request packets destined for this server that have
not yet timed out or received a response. This variable is incremented when an
Access-Request is sent and decremented due to receipt of an Access-Accept,
Access-Reject or Access-Challenge, a timeout or retransmission.

Timeouts

The number of authentication timeouts to this server. After a timeout the client may
retry to the same server, send to a different server, or give up. A retry to the same
server is counted as a retransmit as well as a timeout. A send to a different server is
counted as a Request as well as a timeout.

The number of RADIUS packets of unknown type which were received from this
server on the authentication port

PacketsDropped

UnknownTypes

The number of RADIUS packets of which were received from this server on the
authentication port and dropped for some other reason.

RADIUS Accounting

This window shows managed objects used for managing RADIUS accounting clients, and the current statistics associated
with them. It has one row for each RADIUS authentication server that the client shares a secret with. To view the

RADIUS

Accounting

, click

Monitoring > Port Access Control > RADIUS Accounting

.

230

«
...
241
242
243
244
245
...
»

Содержание DXS-3326GSR - xStack Switch - Stackable































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DXS-3326GSR - xStack Switch - Stackable

Бренд: Garmin Страницы: 2

Бренд: Parkside Страницы: 55

Бренд: Parkside Страницы: 34

Бренд: YASKAWA Страницы: 68

Бренд: Zhone Страницы: 7

Бренд: Zhone Страницы: 1

4-Port 10/100Mbps Ethernet Broadband Router

Бренд: AOpen Страницы: 41

DesignCore RVP-TDA3 Series

Бренд: D3 Страницы: 34

Бренд: Lanner Страницы: 59

Бренд: 3Com Страницы: 12

Бренд: Dynamix Страницы: 102

Бренд: Intellinet Страницы: 2

IKS-6728 Series

Бренд: Moxa Technologies Страницы: 8

Бренд: RouterBOARD Страницы: 4

CU8210-D001-0200

Бренд: Beckhoff Страницы: 25

Бренд: peplink Страницы: 111

Бренд: Bdcom Страницы: 25

DGS-1510 Series

Бренд: D-Link Страницы: 711

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды