D-Link DGS-3700 Series, Справочное руководство, Страница: 517 / 557

DGS-3700 Series Layer 2 Managed Gigabit Ethernet Switch CLI Reference Guide
Page | 517
C
ONNECTIVITY
F
AULT
M
ANAGEMENT
C
OMMANDS
Back to Section Header
The Connectivity Fault Management commands in the Command Line Interface (CLI) are listed (along with
the appropriate parameters) in the following table.
C
OMMAND
P
ARAMETERS
create cfm md <string 22> level <int 0-7>
config cfm md <string 22> {mip [none | auto | explicit] | sender_id [none | chassis | manage |
chassis_manage]}
create cfm ma <string 22> md <string 22>
config cfm ma <string 22> md <string 22> {vlanid <vlanid 1-4094> | mip [none | auto | explicit
| defer] | sender_id [none | chassis | manage | chassis_manage | defer] |
ccm_interval [10ms | 100ms | 1sec | 10sec | 1min | 10min] | mepid_list [add |
delete] <mepid_list>}
create cfm mep <string 32> mepid <int 1-8191> md <string 22> ma <string 22> direction
[inward | outward] port <port>
config cfm mep [mepname <string 32> | mepid <int 1-8191> md <string 22> ma <string 22>]
{state [enable | disable] | ccm [enable | disable] | pdu_priority <int 0-7> |
fault_alarm [all | mac_status | remote_ccm | error_ccm | xcon_ccm | none] |
alarm_time <centisecond 250 -1000> | alarm_reset_time <centisecond 250-
1000>}
delete cfm mep [mepname <string 32> | mepid <int 1-8191> md <string 22> ma <string 22>]
delete cfm ma <string 22> md <string 22>
delete cfm md <string 22>
enable cfm
disable cfm
config cfm ports <portlist> state [enable | disable]
show cfm ports <portlist>
show cfm {[md <string 22> {ma <string 22> {mepid <int 1-8191>}} | mepname <string
32>]}
show cfm remote_mep [mepname <string 32> | md <string 22> ma <string 22> mepid <int 1-8191>]
remote_mepid <int 1-8191>
show cfm fault {md <string 22> {ma <string 22>}}
show cfm port <port> {level <int 0-7> | direction [inward | outward] | vlanid <vlanid 1-4094>}
show cfm mipccm
show cfm pkt_cnt {[ports <portlist>{rx | tx}] | rx | tx | ccm}
clear cfm pkt_cnt {[ports <portlist>{rx | tx}] | rx | tx | ccm}
cfm loopback <macaddr> [mepname <string 32> | mepid <int 1-8191> md <string 22> ma
<string 22>] {num <int 1-65535> | [length <int 0-1500> | pattern <string
1500>] | pdu_priority <int 0-7>}
cfm linktrace <macaddr> [mepname <string 32> | mepid <int 1-8191> md <string 22> ma
<string 22>] {ttl <int 2-255> | pdu_priority <int 0-7>}
show cfm linktrace [mepname <string 32> | mepid <int 1-8191> md <string 22> ma <string 22>]
{trans_id <uint>}
delete cfm linktrace {[md <string 22> {ma <string 22> {mepid <int 1-8191>}} | mepname <string
32>]}