manualshive.com logo in svg

CWSI CP-3500D, Руководство по эксплуатации и установке

Поделиться
Скачать
CWSI CP-3500D Скачать руководство пользователя страница 72

 

P/N IM-C35KD Rev. C 

 2014 Commercial Wireless Systems International, LLC. 

72 

terminals of TB2 across each N.O. alarm output relay A, B and C. The EOL resistor for the trouble 
relay output is wired in series with the Zone 4 input on the SDACT(-2) dialer. The trouble input of the 
CP-3500D will be connected to the N.C. and C terminals of the trouble relay output of the SDACT(-2). 
There is no polarity to this connection. This will allow any dialer trouble to be displayed on the CP-
3500D. 
 

 

Figure 9 

 

7.2.3 Programming 

The programming instructions in this manual are intended to make the interface between the CP-
3500D and Keltron SDACT(-2) UL 864 compliant. You must program the SDACT(-2) with the 
telephone number, account info etc. in order to report to the central station properly. Refer to the 
SDACT(-2) manual for further information. Once the wiring and programming of the CP-3500D and 
SDACT(-2) are complete, any alarms, supervisory or trouble conditions with either the CP-3500D or 
the SDACT(-2) will be communicated off premises to a central station receiver. Only one 
programming change will be required to allow the CP-3500D to be compatible with the SDACT(-2). 
Access the Dialer Setup menu under the CP-3500D Setup screen. Turn the Keltron Dialer Enabled 
option to on and save the setting. This will allow the CP-3500D to communicate through TB5 and 
activate monitoring of the trouble input terminals. There are no software programming or jumper 
changes to make on the Keltron SDACT(-2) for use in a fire alarm only installation. Use the default 
Event Codes and jumper settings. If the CP-3500D is in an installation where Alarm level C is 
programmed for sprinkler supervisory then use the Keltron SDACT(-2) software to change zone 3 
Alarm Event to FS and the Alarm Event Restore for zone 3 to FV.   
 

Содержание CP-3500D
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды