Culligan G1 Series Скачать руководство пользователя страница 54

Страница: 54 / 142

Culligan® Series G1 Reverse Osmosis

Cat. No. 01021713

TDS Programming

The Global RO Controller uses one TDS probe, measuring the product water. The probe is connected via the SBT ter-

minal J20 on the GROC board. The probes are factory installed and calibrated. If the measured TDS levels exceed the

maximum allowed in the product water (see

page 26

), the RO controller displays an error condition (see

“PRODUCT

TDS TOO HIGH” on page 63

RUNNING

JAN-01-12 12:01P

1. From the default home screen, press

. The screen displays the main menu.

1) GO TO RUNNING

2) GO TO OFFLINE

3) INFORMATION

>4) SETUP

2. Press

to scroll to 4) SETUP.

3. Press

to select the SETUP menu.

2) LANGUAGE

3) POWERON MODE

4) FLUSH MODES

>5) ACCESSORIES

4. Press

to select 5)ACCESSORIES. The screen displays the ac-

cessories menu.

3) FLOW METERS

4) SWITCH INPTS

5) PRESS GAUGES

>6) TDS

5. Press

to select 6)TDS. The screen displays the switch inputs

settings.

TDS Probe Settings

Screen Display

Range

Changing the Setting

TDS PROBE:

NONE

None

Product

Both

For the G1 RO, there is only one TDS probe, so the correct setting

is PRODUCT. For the G2 and G3 RO, the correct setting is BOTH.
Press

and then

to change the state if necessary.

ACTUAL TDS OUT

PPM

0–6000 (TDS1)

0–200 (TDS2)

Disconnect the TDS probe from the RO plumbing and submerge it
into a solution of known TDS. Press

to enter the actual TDS

value.

TEMP OFFSET

0 F

-50–50

Use this value to make minor corrections to the displayed temperature

value. For example if you use a handheld temperature device that

shows the water temperature two degrees warmer, change this value

to 2 to compensate.

TEMP COMP VALUE:

0.025

N/A

Please do not change this value unless you are told to do so by Cul-

ligan Rosemont. This value changes the slope used to interpret the

temperature.

RUNNING

JAN-01-12 12:01P

6. Press

to save the settings and return to the home screen.

Содержание G1 Series















































































































































Результаты поиска

Содержание G1 Series

Отзывы:

Culligan G1 Series, Инструкция по установке, эксплуатации и обслуживанию, Страница: 54 / 142

Результаты поиска

Содержание G1 Series

Отзывы: