Culligan G1 Series Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 142

Culligan G1 Series Скачать руководство пользователя страница 57

Accessories

53

Cat. No. 01021713

Multiple Unit ROs

The GBE RO controller supports two multi-unit modes: Two Pass and Alternating.
When in two-pass or alternating mode, the system is configured to support two GBE RO controllers that are connected

together using the communication cable (P/N 01016327). See Figure 31. One of these boards is set as the master, con-

trolling the operations of the other unit, also known as the slave. The slave unit performs as a sensing device.

Two-Pass RO

When in Two-Pass RO mode, the primary unit, identified as the master, issues commands to control the secondary unit,

identified as the slave.

FFLOW

IFLOW

PFLOW

Figure 31.

Two-pass RO process.

Two-Pass RO Start Up Sequence

When configured for two-pass RO, the master unit runs a start up sequence described as follows:

•  The SV1 on the GBE master opens
•  The system waits for the amount of time set on the master as “SV1 Delay”
•  If the pressure-switch-1 shows that pressure is present, then the GBE master turns on the pump for the first unit.
•  The system waits for the amount of seconds set on the master as the “PASS 2 DELAY”.
•  If the pressure-switch-2 shows that pressure is present at pressure-switch-2 then the master sends an operation

command to the slave unit that turns on the second pass pump.

The master will turn off the slave’s motor output any time it detects that one of the inlet pressure switches is off for more

than the specified “PS SW DELAY”. After the slave unit pump turns off, the master will wait three (3) seconds and then

turn off the master pump. The units follow the same procedure if operating conditions trigger the PTLO or the Tank Full

switches.

G1 Series Two-Pass Pairings

NOTE The RO G1 Series Two-Pass requires that the unit have the firmware version FWR202LT04 with a born-

on-date no earlier than FEB 01 2013.

For hardware, plumbing, and wiring, order the following:

Required Kit Part Numbers

Two-Pass Offerings

Feed TDS>500

Feed TDS<500

G1 2L(master), 2S(slave)

01025957

01025959

G1 3L(master), 3S(slave)

01025957

01025959

G1 4L(master), 4S(slave)

01025957

01025959

G1 2F(master), 3L(slave)

01025957

01026007

«
...
55
56
57
58
59
...
»

Содержание G1 Series















































































































































Отзывы:

Нет отзывов