manualshive.com logo in svg

Culligan G1 Series, Инструкция по установке, эксплуатации и обслуживанию, Страница: 50 / 142

Поделиться
Скачать
Culligan G1 Series Скачать руководство пользователя страница 50

 46 

  

Culligan® Series G1 Reverse Osmosis

 46 

 

Cat. No. 01021713

Installing the Modem In the Remote

Open the remote monitor housing by removing the two screws and squeezing the sides of the monitor housing slightly. 

Insert the modem board (P/N 01020307) into the socket on the back of the remote board (see Figure 27). Make sure that 

all of the pins in all four connectors are aligned and make sure the modem is fully seated into all of the sockets. Snap the 

two halves of the remote housing back together using light finger pressure and insert the two screws.

Figure 27. 

Modem installed on back of remote board.

GBE RO Controller Modem Setup

RUNNING

JAN-01-12 12:01P

1.  From the default home screen, press 

. The screen displays the main menu.

 1) GO TO RUNNING

 2) GO TO OFFLINE

 3) INFORMATION 

>4) SETUP

2.  Press 

 

 

 to scroll to 4) SETUP.

3.  Press 

 to select the SETUP menu.

 2) LANGUAGE

 3) POWERON MODE 

 4) FLUSH MODES

>5) ACCESSORIES

4.  Press 

 

 

 

 

 to select 5)ACCESSORIES. The screen displays the ac-

cessories menu.

 1) WIRELESS REM

>2) MODEM

 3) FLOW METERS 

 4) SWITCH INPTS

5.  Press 

 

 to select 2)MODEM. The screen displays the modem settings.

Содержание G1 Series















































































































































Отзывы:

Нет отзывов