Culligan G1 Series Скачать руководство пользователя страница 51

Страница: 51 / 142

Accessories

Cat. No. 01021713

GROC Modem Settings

Screen Display

Range

Changing the Setting

TELEPHONE MODEM

INSTALLED

Installed,

Not

Installed

Press

and then

to select INSTALLED if a telephone modem

is installed inside the Smart Controller.

MODEM CONNECTION

LANDLINE

LandLine

CellModem

Press

and then

to change the Modem connection setting.

See the note on the previous page about analog and digital phone lines.

MODEM LOCATION

IN MAIN CONTROL

In Main

Control

In Remote

Press

and then

to change the Modem Location setting.

Change this setting only if a modem is installed.

TIME zONE GMT

+00:00

0 to +12 or

-12

Press

and then

to specify the time zone of the RO Controller

location with respect to Greenwich Mean Time (GMT).
When using a modem, the controller will occasionally access the Internet to

synchronize the date and time. In order to do this correctly, the control must

be told which time zone it is installed in. The time zone is specified as so many

hours ahead or behind GMT time. The GMT offset for some common cities is

listed below:

GMT Offset

New York

-5:00 (and anywhere in EST)

Chicago

-6:00 (CST)

Denver

-7:00 (MST)

Los Angeles

-8:00 (PST)

London

0:00

Paris

0:00

Rome

+1:00

CALL FREQUENCY

DAILY

Daily

On Error

Daily&Error

Monthly &

Error

Press

and then

to specify the frequency of the RO controller

sending data via modem.

CALL TIME

4:30AM

12:00AM–

11:30PM Press or and then to specify when the RO controller sends data

via modem. The time changes in increments of 30 minutes.

Содержание G1 Series















































































































































Результаты поиска

Содержание G1 Series

Отзывы:

Culligan G1 Series, Инструкция по установке, эксплуатации и обслуживанию, Страница: 51 / 142

Результаты поиска

Содержание G1 Series

Отзывы: