Culligan G1 Series Скачать руководство пользователя страница 60

Страница: 60 / 142

Culligan® Series G1 Reverse Osmosis

Cat. No. 01021713

Alternating RO Unit Settings

RUNNING

JAN-01-12 12:01P

1. From the default home screen, press

. The screen displays the main menu.

1) GO TO RUNNING

2) GO TO OFFLINE

3) INFORMATION

>4) SETUP

2. Press

to scroll to 4) SETUP.

3. Press

to select the SETUP menu.

2) LANGUAGE

3) POWERON MODE

4) FLUSH MODES

>5) ACCESSORIES

4. Press

to select 5)ACCESSORIES. The screen displays the ac-

cessories menu.

5) PRESS GAUGES

6) TDS

7) RELAY MODE

>8) MULT UNIT RO

5. Press

to select 8)MULT UNIT RO. The screen dis-

plays the multiple unit RO settings.

Screen Display

Range

Changing the Setting

MULTI UNIT RO

SINGLE

Single

Two Pass RO

Alternating

Press

and then

to select the RO system

configuration.
For Two-Pass configuration, refer to the Series G1 RO Two-Pass

Kit manual (P/N 01026027).

MUL UNIT RO ROLE

MASTER

Master

Slave

If you select Alternating, press

and then

to select

MASTER if the selected RO will control the functions of the entire

RO system. Select SLAVE if the selected RO will be controlled by

the master RO.

NOTE The Master RO must be set up first.

Содержание G1 Series















































































































































Результаты поиска

Содержание G1 Series

Отзывы:

Culligan G1 Series, Инструкция по установке, эксплуатации и обслуживанию, Страница: 60 / 142

Результаты поиска

Содержание G1 Series

Отзывы: