manualshive.com logo in svg

Culligan G1 Series, Инструкция по установке, эксплуатации и обслуживанию, Страница: 36 / 142

Поделиться
Скачать
Culligan G1 Series Скачать руководство пользователя страница 36

 32 

  

Culligan® Series G1 Reverse Osmosis

 32 

 

Cat. No. 01021713

Setup

After completing the first time setup for the RO, you must also complete the system setup for flush modes, accessories, 

and error limits before completing the initial startup.
Flow Meter K-Factor setting is required during setup. All other RO settings are optional depending on the accessories 

installed. The RO controller does not require any specific setup to run unless accessories are installed or will be installed. 

RO accessories include:

Accessory

Global RO Controller (GROC) Setting

Flush Valves

Setup—>Flush Modes

Flow Meters

Setup—>Accessories—>Flow Meters

Modem

Setup—>Accessories—>Modem

Wireless Remote, RF Board

Setup—>Accessories—>Wireless Rem—>Channel #

Level Controls

Setup—>Accessories—>Switch Inputs

Repressurization System

Setup—>Accessories—>Switch Inputs

Pretreatment Lockout

Setup—>Accessories—>Switch Inputs

Pressure Transducers (G2, G3 only)

Setup—>Accessories—>Press Gauges

System Setup

Set Up Time/Date

If the unit loses time for some reason, you can use this setting to reset the correct date and time. Please note that if you 

have a modem installed and connected to the phone line, the unit will check for the correct time each time it calls in.

RUNNING

JAN-01-12 12:01P

1.  From the default home screen, press  

. The screen displays the main menu.

 1) GO TO RUNNING

 2) GO TO OFFLINE

 3) INFORMATION 

>4) SETUP

2.  Press 

 

 

 to scroll to 4) SETUP.

3.  Press 

 to select the SETUP menu.

>1) TIME/DATE

 2) LANGUAGE

 3) POWERON MODE 

 4) FLUSH MODES

4.  Set Time/Date is the first menu item, so press 

 to select 1) SET TIME/DATE. 

The screen displays the first setting that can be changed.

Time/Date Settings

Screen Display

Range

Procedure

SET

MONTH  

JAN

Jan–Dec

1.  The screen displays the month setting. Press  

  

 or 

 

and then 

 to change the value and see the next setting.

SET

DAY  

 1

1–31

2.  The screen displays the day setting. Press  

  

 or 

 and 

then 

 to change the value and see the next setting.

Содержание G1 Series















































































































































Отзывы:

Нет отзывов