Culligan G1 Series Скачать руководство пользователя страница 128

Страница: 128 / 142

124

Culligan® Series G1 Reverse Osmosis

124

Cat. No. 01021713

>1)GO TO RUNNING

2)GO TO OFFLINE

3)INFORMATION

4)SETUP

2. This is the main menu. The pointer (>) shows where you are in the menu. Press

to scroll through the menu. The selection cursor scrolls down to the next

line or displays the next screen.

3. From a menu screen, press

to select the item next to the cursor. The GROC

screen displays the selected setting or information.

START UP MODE

OFF

4. The GROC screen displays a setting title at the top of the screen and then the set-

ting value. Here we see the current value for the Startup Flush screen is OFF.

START UP MODE

>OFF

5. Press

to turn on the cursor symbol next to the setting value. The cursor indi-

cates that you can change the current value using

START UP MODE

>ON

6. Press

once. The screen displays the new setting value next to the cursor.

START UP MODE

>OFF

7. Press

again. The screen displays the next available setting value.

8. You may press

to scroll through all of the available options for the

screen.

START UP MODE

OFF

9. Press

to accept the selected screen value. The cursor next to the value is

removed.

STANDBY MODE

OFF

10. If other settings are available, press

to advance to the next displayed setting.

>1)GO TO RUNNING

2)GO TO OFFLINE

3)INFORMATION

4)SETUP

11. Press

to exit from the setting. The GROC screen displays the parent menu.

RUNNING

JAN-01-12 12:01A

12. Press

repeatedly to return to the home screen.

Содержание G1 Series















































































































































Результаты поиска

Содержание G1 Series

Отзывы:

Culligan G1 Series, Инструкция по установке, эксплуатации и обслуживанию, Страница: 128 / 142

Результаты поиска

Содержание G1 Series

Отзывы: