manualshive.com logo in svg

Culligan G1 Series, Инструкция по установке, эксплуатации и обслуживанию, Страница: 12 / 142

Поделиться
Скачать
Culligan G1 Series Скачать руководство пользователя страница 12

 8 

  

Culligan® Series G1 Reverse Osmosis

 8 

 

Cat. No. 01021713

Pump/Motor Panel

Hang the pump motor panel on the mounting bracket. The top edge of panel hooks on to the bracket. See Figure 5.

Mounting Bracket

Motor Panel

Figure 5. Pump motor panel hanging on mounting bracket. 

Fittings

Locate the Membrane Fitting Kit that was shipped with the unit. This kit includes all the fittings needed to connect the 

membranes to the pump/motor panel. Refer to

 Figure 11 on page 13

 through 

Figure 15 on page 17

 for the model 

you are installing and follow the tubing diagram. Detailed drawings of the fittings and housings can be found in the parts 

section.

Prefilter Cartridge

1.  Locate the prefilter cartridge packed with the main unit. 
2.  Unscrew the prefilter bowl. 
3.  Lubricate the seal ring with silicone lubricant as required. 
4.  Remove the paper wrapper from the cartridge, place the cartridge in the bowl, and screw the bowl onto the 

head.

Pressure

Relief

Button

Inlet

Outlet

Filter Cartridge

Figure 6.  Installing the Prefilter.

Содержание G1 Series















































































































































Отзывы:

Нет отзывов