Culligan G1 Series Скачать руководство пользователя страница 23

Страница: 23 / 142

GBE RO Controller Program Data

Cat. No. 01021713

GBE RO Controller Program Data

Program Data Input

There are a few items to note that can make programming the Culligan

Global RO Controller easier:

Slew Rates

This term refers to the speed at which the display moves through the input of material. For ex-

ample, holding down the up arrow key for (5) seconds when inputting minutes for Time of Day

will cause the minutes to pass in (10) minute blocks of time. Press the up arrow or down arrow

keys for shorter periods (less than 5 seconds) will slow the rate. To move through the program-

ming slowly, do not hold down the up arrow or the down arrow keys.

Beeper

A beeper is available to assist the user by providing an audible tone (about 70 decibels) to signi-

fy valid (one beep) and invalid (three beeps) key presses. The beeper can be deactivated in the

programming mode. (If error occurs, beep will still sound even if set to “No” programming.)

Programming

Mode Timeout

If there is no keypad activity for a one (1) minute period while in the programming mode, the

controller will exit the programming mode and return to the main display. Any setting that was

changed prior to the control timing out will revert to the original value. Pressing the CHECK

MARK button saves the setting.

Program Input

Acceptance

For programming information to be accepted, the check mark key must be depressed prior to

programming mode timeout.

Содержание G1 Series















































































































































Результаты поиска

Содержание G1 Series

Отзывы:

Culligan G1 Series, Инструкция по установке, эксплуатации и обслуживанию, Страница: 23 / 142

Результаты поиска

Содержание G1 Series

Отзывы: