Culligan G1 Series Скачать руководство пользователя страница 67

Страница: 67 / 142

Service and Maintenance

Cat. No. 01021713

Error Codes

When the G Series RO Controller encounters an error, the screen displays a PROBLEM FOUND message.
Press to scroll to the error message.

STANDBY

JAN-01-12 1:55P

Problem Found

No Remote Signal

REJECTION RATE LOW

This message is triggered when the rejection rate goes below the value set in MIN RE-

JECT %. This indicates the membranes should be cleaned.

RECOVERY RATE HIGH

This message is triggered when the recovery percentage goes above the value set in MAX

RECOVERY %. This could indicate a change in water chemistry, temperature, or acciden-

tal setting change.

RECOVERY RATE LOW

This message is triggered when the recovery percentage goes below the value set in MIN

RECOVERY %. This could indicate a change in water chemistry, temperature, accidental

setting change, or that the membrane is fouling.

PRODUCT TDS TOO

HIGH

This message is triggered when the product TDS goes above the value set in MAX TDS

OUT. This indicates that the membranes may be getting fouled and are losing their rejec-

tion capability.

NO REMOTE SIGNAL

This message is triggered when the system and the wireless remote lose contact. An op-

tional wireless remote must be installed to see this message.

FEED QUALITY LOW

In a multiple-RO configuration, the master will command the slave to turn off its aux output

if the feed quality input signal reported by the slave remains triggered for more than 5

minutes.

All of the above conditions initiate an alert that will be sent back to the dealership if the telemetry (modem) options are set

up, and the RO will shut down. User intervention is required to restart the RO. See Installing Modem for information about

setting up this feature. Additional fees apply.

Содержание G1 Series















































































































































Результаты поиска

Содержание G1 Series

Отзывы:

Culligan G1 Series, Инструкция по установке, эксплуатации и обслуживанию, Страница: 67 / 142

Результаты поиска

Содержание G1 Series

Отзывы: