Cub Cadet Tank S S7237 Скачать руководство пользователя

Страница: 33 / 48

ectiOn

6 — M

aintenance

& a

djustMents

Side to Side Leveling

Park the mower on a flat paved surface, engage the

parking brake, shut off the engine, remove the key from the

ignition switch, disconnect the spark plug wires and using

the power implement lift, position the mowing deck into

the 4” height of cut position. (The 4” height of cut position

is recommended in order for one to see and obtain a

measurement. Any height of cut position is acceptable as

long as a proper measurement can be taken.)
Measure blade-to-ground height at the front tip of the

right blade. To obtain an accurate measure, align blades in

parallel with mower centerline, (i.e. front to back).
Measure blade-to-ground height at the front tip of the left

blade. Be sure to measure at the blade tip with the blades

arranged in proper position.
Adjust the eyebolt at the left front of the deck so that the

blade-to-ground height at the right front blade tip matches

that of the left front blade tip. This is done by loosening the

jam nuts on the eyebolt and tightening the upper nut to

raise the deck and loosening the nut to lower the deck. The

right front blade tip height is fixed so you must adjust the

left front tip to match it. See Fig. 6-7.

Once the proper adjustment is made, re-tighten the lower

jam nut.

Front to Back Leveling

Measure the blade-to-ground height at the right rear blade

tip. Again be sure to measure at the blade tip at the rear of

the right blade when aligned along the mower centerline.

The blade-to-ground height at the rear of the blade tip

should be 1⁄8

” to

1⁄4

” higher than the front tip. This is referred

to as blade pitch. The same height difference should be

true for the left blade, measured front and back. The pitch

should not exceed 1⁄16

” if cut height is below 1-

1⁄2

”.

Clean the engine and the entire tractor thoroughly.

NOTE:

Use of a pressure washer or garden hose is not

recommended to clean your tractor. They may cause

damage to electrical components, spindles, pulleys,

bearings or the engine. The use of water will result in

shortened life and reduce serviceability.

Sharpen the blades so that the mower will be ready to use

when needed.

Protect the metal surfaces. Repair scratches with the

appropriate touch-up spray paint. Brush a rust preventive

oil on any unpainted surfaces including the pulleys and

blades. (Be careful not to get any oil on the drive belts.)

Clean and fully charge the battery, then disconnect the

negative cable at the battery to prevent possible discharge.

Recharge the battery periodically when in storage.

NOTE:

Remove the battery if exposed to prolonged periods

of sub-freezing temperatures. Store in a cool, dry location

where temperatures are above freezing.
Lubricate all lubrication points.

Inspect the hydraulic hoses, lines and fittings. Replace as

necessary.

Jack the mower up and store it on blocks to take the weight

10.

off of the tires.

Removing The Tractor From Storage

Check the battery. Charge if necessary.

Lower tractor off blocks, and inflate the tires to the

recommended pressure.
Remove the spark plugs and wipe them off. Using the

starter, crank the engine to pump the excess oil out of the

spark plug holes. Replace the spark plugs and the ignition

leads.

If removed before storing, replace the LPG tanks.

Check the level of the engine oil in the crankcase and the

hydraulic reservoir tank.

Start the engine and allow to idle for a few minutes to

ensure engine is operating properly.
Drive the tractor without a load to make certain all the

tractor systems are functioning properly.

Adjustments

Adjusting the Seat

Refer to the Assembly & Set-Up section for instructions on

adjusting the seat.

Adjusting the Steering Wheel

Refer to the Assembly & Set-Up section for instructions on

adjusting the steering wheel.

Leveling the Mower Deck

When correctly adjusted the mower deck should be level side to

side, and the front of the deck should be approximately 1⁄4

” lower

than the rear of deck.

NOTE:

Check the tractor’s tire pressure before performing any

deck leveling adjustments. See the tire side wall for proper

inflation pressures.

Left Front of the Deck

Eye Bolt

Upper

Jam Nut

Lower Jam Nut

Figure 6-7

Содержание Tank S S7237

















































Результаты поиска

Содержание Tank S S7237

Отзывы:

Похожие инструкции для Tank S S7237

Бренды по названию

Популярные бренды

Cub Cadet Tank S S7237, Руководство оператора

Результаты поиска

Содержание Tank S S7237

Отзывы:

Похожие инструкции для Tank S S7237

Бренды по названию

Популярные бренды