Crystal Vision TANDEM-300 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 90

background image

Crystal Vision

Using card edge controls

TANDEM-300 User Manual R1.2

35

14/02/2008

If a setting is adjusted by mistake, changing the menu (piano MENU or SEL switches)
will discard the unwanted setting, providing this is done before Menu switch 1 has been
toggled down and up. After a setting has been saved to memory, it can only be ‘undone’
by re-selecting the previous setting and saving it again by toggling Menu switch 1 again.

The card edge display codes

A condensed code is used to maximise the information that can be shown on the ten-bit
status display. Codes used for sources and destinations are as follows:

Code

Meaning

Comments

An

De-embedded audio source on side 1

Bn

De-embedded audio source on side 2

Cn

Embedded audio destination on side 1

Dn

Embedded audio destination on side 2

Not available with TANDEM-300

Gn

Option card audio source on side 1

Option card must be AIP2, DIP2 or RS4

Hn

Option card audio source on side 2

Option card must be AIP2, DIP2 or RS4

In

Option card audio destination on side 1

Option card must be AOP2, DOP2-75/110

Jn

Option card audio destination on side 2

Option card must be AOP2, DOP2-75/110

M1 - 4

Stereo to mono converter

Mono source or destination

1.1

AES 1 or Stereo Pair 1 on side 1

Each analogue or digital output has two
buffered outputs (labelled a & b) which may be
available at the rear connector. Please see the
Installation section for connector details.

1.2

AES 2 or Stereo Pair 2 on side 1

2.1

AES 1 or Stereo Pair 1 on side 2

2.2

AES 2 or Stereo Pair 2 on side 2

‘ ’n

New audio group

Group n does not exist in the SDI stream

=n

Existing audio group

Group n already exists in the SDI stream

Note:

n denotes “1 2 3 4” individual active mono channels.

Note:

An update will be required to discuss Dual SDI mode selection when implemented.

«
...
34
35
36
37
38
...
»

Содержание TANDEM-300



























































































Отзывы:

Нет отзывов

Похожие инструкции для TANDEM-300

Бренд: Ubiquiti Страницы: 24

C50FSi - VB Network Camera

Бренд: Canon Страницы: 32

Бренд: Rabbit Страницы: 120

Бренд: GE Страницы: 93

Бренд: Parker Страницы: 344

SCSI PC Card REX-9530V

Бренд: Ratoc Systems Страницы: 30

ILDA Gem Laser projector tool

Бренд: Stanwax Laser Страницы: 3

eBOX532-100-FL Series

Бренд: AXIOMTEK Страницы: 2

Бренд: Parker Страницы: 50

Бренд: Paradyne Страницы: 10

Бренд: EVOC Страницы: 57

Бренд: red lion Страницы: 5

Бренд: Technics Страницы: 20

PXI Terminal Block NI TB-2709

Бренд: National Instruments Страницы: 12

Бренд: Sony Ericsson Страницы: 2

Бренд: Digisol Страницы: 73

Бренд: Netequalizer Страницы: 14

Бренд: C&H Technologies Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды