manualshive.com logo in svg

Cradlepoint COR IBR350, Руководство пользователя

Cradlepoint COR IBR350 - надежный маршрутизатор для бизнеса. Бесплатно загрузите руководство по эксплуатации на нашем сайте. Получите информацию о настройке и использовании этого продукта для оптимальной производительности вашей сети. Посетите manualshive.com для скачивания.

Поделиться
Скачать
background image

ModemSettings

Not all modems will have all of the options shown below; the available options are specific to the modem type.

OnDemand

: When this mode is selected a connection to the Internet is made as needed. When this mode is not selected a connection to the

Internet is always maintained.

IP WAN SubnetFilter

: This feature will filter out any packets going to the modem that do not match the network (address and netmask).

AggressiveReset

: When Aggressive Reset is enabled the system will attempt to maintain a good modem connection. If the Internet has been

unreachable for a period of time, a reset of the modem will occur in attempt to re-establish the connection.

Automaticallycheckfornewfirmware

: (Default: selected) The modem will automatically check for firmware updates by default.

EnableAuxAntenna

: (Default: selected) Enable or disable the modem’s auxiliary diversity antenna. This should normally be left enabled.

GPS SignalSource

: Select the antenna to be used for receiving GPS coordinates. Some products support a dedicated GPS antenna, while others

use the auxiliary diversity antenna only (and some products support both).

EnableeHRPD

: (Default: selected) Enable or disable the modem’s ability to connect via eHRPD (enhanced High Rate Packet Data) when connecting

to a 3G EVDO network on Sprint. eHRPD routes EVDO traffic through the LTE systems, enabling easy transitions between LTE and EVDO. In rare
cases it may make sense to bypass the LTE core, so this field allows you to disable eHRPD.

ModemConnectionMode

: Specify how the modem should connect to the network. Not all options are available for all modems; this will default

to Auto if an incompatible mode is selected.

•

Auto(allmodes)

: Let the modem decide which network to use.

•

Auto3G (3G orless)

: Let the modem decide which 2G or 3G network to use. Do not attempt to connect to LTE.

•

ForceLTE

: Connect to LTE only and do not attempt to connect to 3G or WiMAX.

•

ForceWiMAX

: Connect to WiMAX only and do not attempt to connect tot 3G or LTE.

•

Force3G (EVDO,UMTS,HSPA)

: Connect to 3G network only.

•

Force2G (1xRTT,EDGE,GPRS)

: Connect to 2G network only.

NetworkSelectionMode

: Wireless carriers are assigned unique network identifying codes known as PLMN (Public Land Mobile Network). To

manually select a particular carrier, select the Manual radio button and enter the network PLMN. Choose from the following options:

•

None/NoChange

•

Auto

: Selected by default

•

Homeonly

•

Manual

: Input the PLMN code

FunctionalMode

: Selects the functional mode of the modem. IPPT (IP passthrough) mode causes the modem to act as a transport, passing

Internet data and IP address information between the modem and the Internet directly. NAT mode causes the modem to NAT the IP address
information. Consequently, IPPT mode does not allow user access to the modem web UI and NAT mode does allow user access to the modem

web UI.

•

None/NoChange

•

IPPT

•

NAT

Network-InitiatedAlerts

: This field controls whether the Sprint network can disconnect the modem to apply updates, such as for PRL, modem

firmware, or configuration events. These activities do not change any router settings, but the modem connection may be unavailable for periods
of time while these updates occur. The modem may also require a reset after a modem firmware update is complete.

•

Disabled

: The request to update will be refused.

87

Содержание COR IBR350





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для COR IBR350

2Wire 2701HGV-W Installation Manual preview
2701HGV-W
Бренд: 2Wire Страницы: 30
HALNy HLE-3GM Quick Installation Manual preview
HLE-3GM
Бренд: HALNy Страницы: 8
ICU tech Weblog GW3 User Manual preview
Weblog GW3
Бренд: ICU tech Страницы: 17
OlenCom MG-iP Series Reference Manual preview
MG-iP Series
Бренд: OlenCom Страницы: 299
DEUTSCHMANN AUTOMATION UNIGATE IC - Powerlink Instruction Manual preview
UNIGATE IC - Powerlink
Бренд: DEUTSCHMANN AUTOMATION Страницы: 50
Matrix simado gfx11 System Manual preview
simado gfx11
Бренд: Matrix Страницы: 88
Yeastar Technology NeoGate TG100 Installation Manual preview
NeoGate TG100
Бренд: Yeastar Technology Страницы: 14
Advantech ADAM-4570 User Manual preview
ADAM-4570
Бренд: Advantech Страницы: 74
Vantron VT-M2M-C335 User Manual preview
VT-M2M-C335
Бренд: Vantron Страницы: 15
HELIX FI Installation Manual preview
FI
Бренд: HELIX Страницы: 12
Check Point QUANTUM SPARK 1600 Administration Manual preview
QUANTUM SPARK 1600
Бренд: Check Point Страницы: 285
Comelit 1456 Technical Manual preview
1456
Бренд: Comelit Страницы: 28
TEKTELIC Communications KONA ENTERPRISE T0007242 User Manual preview
KONA ENTERPRISE T0007242
Бренд: TEKTELIC Communications Страницы: 15
Endress+Hauser FieldGate SWG50 Operating Instructions Manual preview
FieldGate SWG50
Бренд: Endress+Hauser Страницы: 48
ZyXEL Communications 2R-P1C User Manual preview
2R-P1C
Бренд: ZyXEL Communications Страницы: 53
SICK WI180C-IOB01 Quick Start preview
WI180C-IOB01
Бренд: SICK Страницы: 4
Unique Lighting Systems SMRT Logic LPLUS Quick Reference & Setup Manual preview
SMRT Logic LPLUS
Бренд: Unique Lighting Systems Страницы: 4
Samsara AG24 Install Manual preview
AG24
Бренд: Samsara Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды