Cradlepoint COR IBR350 Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 148

Cradlepoint COR IBR350 Скачать руководство пользователя страница 77

IP Version

: Select IPv4 or IPv6. Depending on your selection, you have diﬀerent options for deﬁning the address range.

IP/NetworkAddress

or

IPv6Address

: The IP address of the target network or host. The IPv6 address ﬁeld includes

CIDR notation

to declare a

range of addresses.

Netmask

: The Netmask, along with the IPv4 address, deﬁnes the network the computer belongs to and which other IP addresses the computer

can see in the same LAN. An IP address of 192.168.0.1 along with a Netmask of 255.255.255.0 deﬁnes a network with 256 available IP addresses
from 192.168.0.0 to 192.168.0.255.

NOTE:255.255.255.255isusedtosignifyonlythehostthatwasenteredintheIP/NetworkAddressﬁeld.

Gateway

or

IPv6Gateway

: Speciﬁes the next hop to be taken if this route is used. A gateway of 0.0.0.0 implies there is no next hop, and the IP

address matched is directly connected to the router on the interface speciﬁed:

LAN

or

WAN

.

Device

: Select the network interface from the dropdown menu (e.g. ethernet-wan). You can use this instead of deﬁning the IP address, especially

in cases when the IP address is changing.

Metric

: Set the numerical priority of the route. Lower numbers have higher priority.

AllowNetworkAccess

: (Default: Deselected.) Some static routes will need an IP Filter Rule via the Firewall to allow packets through the route

without being blocked. Selecting this option automatically creates this IP Filter Rule. If the

IP/NetworkAddress

falls outside the LAN IP range,

you probably need to select this option.

Distribute

: Allow this static route to be distributed via a routing protocol (

NetworkSettings>RoutingProtocols

).

Internet

The Internet section of the Administration Pages provides access to tools for controlling the WAN (Wide Area Networks). The Internet tab has the
following dropdown menu items:

•

Connection Manager

•

Client Data Usage

•

Data Usage

•

GRE Tunnels

•

Network Mobility (NEMO)

•

VPN Tunnels

ConnectionManager

The router can establish an uplink via Ethernet, WiFi as WAN, or 3G/4G modems (integrated or external USB). If the primary WAN connection fails,
the router will automatically attempt to bring up a new link on another device: this feature is called

failover

. If Load Balance is enabled, multiple

WAN devices may establish a link concurrently.

77

«
...
75
76
77
78
79
...
»

Содержание COR IBR350





















































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды