Cradlepoint COR IBR350 Скачать руководство пользователя | Manualshive

Страница: 128 / 148

background image

SMS

SMS (Short Message Service, or text messaging) requires a cellular modem with an active data plan. SMS is not designed to be a full remote
management feature: SMS allows you to connect to the router for a few simple queries or commands with a text messaging service (e.g., from your
phone). A modem that does not have an active data connection may still be reachable by SMS because Internet traﬃc and SMS traﬃc operate on
separate channels, so SMS can be used to bring on oﬄine router back online.

SMS is enabled on the router by default. However, it only works if SMS is supported and enabled on the modem. Most modems have SMS enabled
by default, but the carrier may charge a fee for each text message sent or received. Contact your carrier to review these fees and/or to enable an
SMS plan.

ImportantnotesaboutSMS:

• Messages are limited to 160 characters.
• SMS is not a guaranteed delivery protocol. The carriers do not guarantee that the SMS message will be delivered to the modem or that

the modem’s response will be delivered to the sender. This means an administrator might have to send messages multiple times before the
desired action is performed.

• SMS is a slow protocol. It can take seconds or up to a few minutes for messages to be delivered.
• SMS messages are not encrypted; they are sent in full readable text over the network.

Figure 157: SMS Alert Settings

EnableSMS support

– SMS support is enabled by default on the router. Deselect this to disable.

Password

– By default, the password is the last 8 characters of the router’s MAC address (i.e., the Default Password on the product label). You

can change this password to anything between 1 and 16 characters. It should be long enough to be useful for security but short enough to easily
type into your phone (or other texting client).

WhiteList

– This list is blank by default, which means that the router will accept SMS messages from any phone number. Leaving this blank is

unsecure, so Cradlepoint recommends that you add phone numbers to this list. Once any numbers are listed, only those numbers have the ability
to connect to the router via SMS.

NOTE:YoucannotaddemailaddressestotheWhitelist. WhenaphonenumberisaddedtotheWhiteList, emailSMS messageswillberejected.

HowtoSendanSMS Message

You can send SMS messages to the router via phone or email. The key elements are:

1. the modem’s MDN
2. the SMS password (deﬁned above)
3. the command

You must know the MDN (Mobile Directory Number) of the modem to send SMS messages to the router. This is a phone number that can be found

under

Status>InternetConnections

in the router administration pages or under

Devices>NetworkInterfaces

in Enterprise Cloud Manager.

128

«
...
126
127
128
129
130
...
»

Содержание COR IBR350





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для COR IBR350

Бренд: Net2Phone Страницы: 23

Бренд: Top Global Страницы: 75

Response Mk2 One-Port

Бренд: ETC Страницы: 8

Бренд: IPitomy Страницы: 4

Бренд: Dinstar Страницы: 100

Бренд: Grandstream Networks Страницы: 54

Бренд: Handlink Technologies Страницы: 60

Бренд: NKE Страницы: 14

Бренд: Ericsson Страницы: 12

Selenio VMG-14+

Бренд: Imagine communications Страницы: 92

Бренд: Comtrend Corporation Страницы: 70

Бренд: ViewSonic Страницы: 57

Бренд: Zoom Страницы: 2

Бренд: Wireless Devices Страницы: 32

Бренд: Riello UPS Страницы: 14

IQ Combiner 3C-ES

Бренд: enphase Страницы: 8

Бренд: enphase Страницы: 32

Бренд: Lantronix Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды