Cooper Lighting WaveLinx Lite Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 78

Cooper Lighting WaveLinx Lite Скачать руководство пользователя страница 33

User Manual: WaveLinx Lite (1.5)

www.cooperlighting.com

33

Note

: If a wallstation is programmed for a zone level, raise level or lower level action type to a specific zone, that zone will not allow deletion until the

wallstation action is changed, displaying a warning message on the screen. Adjust the wallstation programming per the instructions on page 45 to

change the wallstation button actions and then delete the zone.:

Modify Devices

After devices are provisioned, it is possible to change the device name. Devices may also be deleted, returning them to an unprovisioned state.

For details on moving a device to a different zone, refer to page 31.
Internet connection is not needed to modify a device but connection to the WaveLinx Lite device/network is required. The mobile device will

need to be in range and as close as possible (within 60 feet) to one of the WaveLinx Lite devices that belongs to the same area

Rename Devices

Optionally devices may be given a more descriptive name to help with identifying the device location or function.
To change a device name:
1: Bring the mobile device within range (within 60 feet) of any provisioned WaveLinx Lite device in the desired area.
2: Ensure that the mobile device Bluetooth is turned on, and then open the WaveLinx Lite Mobile Application.
3: In the site list, select a site.
4: In the area list, select the desired area. After a short delay, verify that the area shows that the mobile application is connected to the network.
Tap on the icon if it is necessary to refresh the connection.
5: If the device is a wallstation, scroll down to the ‘Devices in Area’ section. If the device is a control device (light fixtures with a fixture mount or

integrated sensor, for example), in the zone list, select the zone that the device is assigned to.

«
...
31
32
33
34
35
...
»

Содержание WaveLinx Lite















































































Отзывы:

Нет отзывов