Cooper Crouse-Hinds D2 W MDME 2400 1 Скачать руководство пользователя страница 8

Страница: 8 / 85

D2 W MDME 2400 Wireless Ethernet Modem

IF 1584 Rev. 1

Page 8

1.2

Getting Started Quickly

Most applications for the D2 W MDME 2400 require little configuration. The D2 W MDME 2400
has many sophisticated features; however, if you don’t require these features, this section will allow
you to configure the units quickly.

First, read Section 2, “Installation.” The D2 W MDME 2400 requires an antenna and a power
supply.

Power the D2 W MDME 2400 and make an Ethernet connection to your PC (for further
information on how to do this, refer to Section 3.4).

Set the D2 W MDME 2400 address settings as per Section 3.4.

Save the configuration - the D2 W MDME 2400 is now ready to use.

Before installing the D2 W MDME 2400, bench test the system. It is a lot easier to locate problems
when the equipment is all together.

There are other configuration settings which may or may not improve the operation of the system.
For details on these settings, refer to Section 3.

Содержание D2 W MDME 2400 1






















































































Результаты поиска

Содержание D2 W MDME 2400 1

Отзывы:

Бренды по названию

Популярные бренды

Cooper Crouse-Hinds D2 W MDME 2400 1, Руководство пользователя

Результаты поиска

Содержание D2 W MDME 2400 1

Отзывы:

Бренды по названию

Популярные бренды