manualshive.com logo in svg

Cooper Crouse-Hinds D2 W MDME 2400 1, Руководство пользователя

Поделиться
Скачать
Cooper Crouse-Hinds D2 W MDME 2400 1 Скачать руководство пользователя страница 51

 Chapter Three 

Operation 

 

Page 51 November 

2008 

 

 

 

 

 

 

 

 

 

 

 

The above example demonstrates how a Modbus/TCP Client (Master) can connect to one or more 
Modbus RTU (i.e. serial) Slaves.  In this example, the D2 W MDME 2400 Access Point is 
configured with the “RS232 Modbus/TCP to RTU Gateway” enabled.  Once enabled, the gateway 
converts the Modbus/TCP queries received from the Master into Modbus RTU queries and 
forwards these over the RS232 port to the Slave.  When the serial response to the query arrives 
from the Slave, it is converted to a Modbus/TCP response and forwarded via the network to the 
Modbus/TCP Master.  If no response was received serially by the D2 W MDME 2400 within the 
configured Response Timeout, the D2 W MDME 2400 will initiate a number of retries specified by 
the configured Maximum Request Retries. 

The Modbus TCP to RTU Gateway may be configured to operate on either the RS232 or RS485 
port.  It does not support operation on both ports at the same time.

 

Enable RS232 Modbus TCP 
to RTU Gateway 

Check this box to enable the Modbus TCP to RTU Gateway on the 
RS232 port.  Only a single serial port is allowed at a time. 

Enable RS485 Modbus TCP 
to RTU Gateway 

Check this box to enable the Modbus TCP to RTU Gateway on the 
RS485 port.  Only a single serial port is allowed at a time. 

Data Rate 

The serial data rate desired.  Serial data rates available range from 
110bps to a maximum of 115,200bps. 

Data Bits Parity Stop Bits 

The data format desired.  Data formats of 8N1, 7E1, 7O1, 7E2, 7O2 are 
supported. 

Pause Between Requests 

Enter the delay between serial request retries in milliseconds 

Response Timeout 

Enter the serial response timeout in milliseconds – a serial retry will be 
sent if a response is not received within this timeout. 

Connection Timeout 

Enter the TCP connection timeout in seconds – if no Modbus/TCP data 
is received within this timeout, then the TCP connection will be 
dropped.  Set this field to zero for no timeout. 

Maximum Request Retries 

Enter the maximum number of request retries performed serially. 

Maximum Connections 

Enter the maximum number of simultaneous TCP connections to the 
server allowed. 

 

 

Client

LAN

 

Modbus/TCP Client 

(Master)

 

RS232 
Modbus 
RTU

 

Slave 

RS232 
Modbus/TCP to 
RTU Gateway

Access 

Point

Содержание D2 W MDME 2400 1






















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды