manualshive.com logo in svg

Cooper Crouse-Hinds D2 W MDME 2400 1, Руководство пользователя

Поделиться
Скачать
Cooper Crouse-Hinds D2 W MDME 2400 1 Скачать руководство пользователя страница 58

D2 W MDME 2400 Wireless Ethernet Modem 

IF 1584 Rev. 1

 

IF 1584 Rev. 1 

Page 58 

Click on Factory Default Configuration Reset, and wait for unit to reset.  When reset, the LINK 
LED will flash. 

Extending a Wired Network 

Access Point Configuration. 

Connect straight-through Ethernet cable 
between PC and D2 W MDME 2400. 

•

 

Ensure configuration PC and D2 W MDME 
2400 are set up to communicate on the 
same network. 

•

 

Set dip switch to SETUP mode.  

•

 

Power up unit, and wait for LINK LED to 
cease flashing. 

•

 

Adjust PC network settings. 

Set Configuration PC network card with network setting of IP address 192.168.0.1, netmask 
255.255.255.0. 

•

 

Open configuration web page with Internet Explorer at address http://192.168.0.1XX/, where 
XX is the last two digits of the serial number. 

When prompted for password, enter default username “user” and password “user.” 

Enter “Network,” and select Operating Mode as Access Point.   

Select Device Mode as Bridge. 

Change the Gateway IP Address to 192.168.0.1. 

Change the Ethernet and Wireless IP addresses to 192.168.0.200. 

Change Ethernet and Wireless Subnet masks to 255.255.255.0. 

Enter a System Address (SSID) string. 

Select the Radio Encryption required. 

Set dip switch to RUN. 

Save the changes and unit will restart with new settings. 

LAN HUB 

192.168.0.0 

255.255.255.0

Ethernet Device

Access Point 

Bridge

 

Client 1

Bridge

Client 2

Bridge

Содержание D2 W MDME 2400 1






















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды