manualshive.com logo in svg

Cooper Crouse-Hinds D2 W MDME 2400 1, Руководство пользователя

Поделиться
Скачать
Cooper Crouse-Hinds D2 W MDME 2400 1 Скачать руководство пользователя страница 74

D2 W MDME 2400 Wireless Ethernet Modem 

IF 1584 Rev. 1

 

IF 1584 Rev. 1 

Page 74 

  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5.

 

There are two options:  

 

a.

 

The “Save to Flash and Reset” button may be clicked, to initiate a reset immediately after 
a successful Firmware upgrade so that the new firmware is run.  

 

b.

 

Alternatively, click “Save to Flash” button to just program the new Firmware to the unit.  
A reset is necessary to run the new Firmware.  This is useful for maintaining radio link 
while performing upgrades to remote units. 

 

6.

 

The following dialog box may be displayed as a warning.  Click OK to proceed. 

 

 

 

7.

 

Firmware upgrade will proceed, and should take about 1 minute if performed locally.  If 
performed over a radio link, the upgrade may take longer, depending upon the quality of the radio 
link and the amount of traffic on the network.  

 

Содержание D2 W MDME 2400 1






















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды