manualshive.com logo in svg

Cooper Crouse-Hinds D2 W MDME 2400 1, Руководство пользователя

Поделиться
Скачать
Cooper Crouse-Hinds D2 W MDME 2400 1 Скачать руководство пользователя страница 18

D2 W MDME 2400 Wireless Ethernet Modem 

IF 1584 Rev. 1

 

IF 1584 Rev. 1 

Page 18 

How a Link Connection is Lost. 

The Access Point refreshes the link status with a Client every time a message is received from that 
Client.  If nothing is received from a Client for a period of 120 seconds, the Access Point sends a 
“link-check” message.  If there is no response to the link-check, a de-authenticate message is sent 
and the link is dropped. 

A Client monitors beacons from an Access Point to determine whether the link is still present.  If 
the Client can no longer receive beacons from the AP, the AP is considered to be out of range and 
the link is dropped.  Whenever a Client is not connected to an AP, it will cyclically scan all 
available channels for a suitable AP. 

Roaming. 

Clients may also 

roam 

between Access Points.  If a Client receives a beacon from an AP with a 

stronger signal than the current AP (providing SSID is the same and capability information is 
compatible), it may disconnect from the first AP and establish a link with the second AP.  This 
functionality permits a Client to have mobility while maintaining a link with the most suitable AP. 

LED Indication. 

The following table details the status of the indicating LEDs on the front panel under 

normal

 

operating conditions. 

LED Indicator

 

Condition

 

Meaning

 

OK  

GREEN 

Normal operation 

OK 

RED 

Supply voltage too low 

Radio RX 

 GREEN flash 

Radio receiving data 

Radio RX 

RED flash 

Weak radio signal 

Radio TX 

Flash 

Radio transmitting 

Radio LINK 

ON 

On when a radio communications link is 

established 

Radio LINK 

OFF 

Communications failure or radio link not 

established 

Radio LINK 

GREEN flash  

RED flash 

Serial port receiving  

CTS low 

LAN 

ON 

Link established on Ethernet port 

LAN 

Flash 

Activity on Ethernet port 

Serial  

GREEN flash 

RS232 serial port activity 

Serial  

RED flash 

RS485 serial port activity 

DIO ON 

Digital output ON 

or

 input is grounded 

Содержание D2 W MDME 2400 1






















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды