manualshive.com logo in svg

Cooper Crouse-Hinds D2 W MDME 2400 1, Руководство пользователя

Поделиться
Скачать
Cooper Crouse-Hinds D2 W MDME 2400 1 Скачать руководство пользователя страница 40

D2 W MDME 2400 Wireless Ethernet Modem 

IF 1584 Rev. 1

 

IF 1584 Rev. 1 

Page 40 

3.10

 

                    Routing Rules 

When a D2 W MDME 2400 receives an IP frame that is destined for an IP address on a different 
network, it checks if the network address matches the network address of one of its own interfaces 
(i.e. hard-wired Ethernet, wireless Ethernet, or WDS), and forwards the frame appropriately.  
However, if the IP network address does not match any of its interfaces, the D2 W MDME 2400 
will forward the frame to its default gateway.  In this case, it is assumed that the default gateway 
has a valid route to the destination. 

In some cases, it is not practical to have just one default gateway (i.e. routed wireless networks with 
more than two D2 W MDME 2400 routers; and in some cases, when WDS router interfaces are 
used).  If more than one “next-hop router” is required, the D2 W MDME 2400 allows for up to 30 

routing rules

 to be configured.  A routing rule specifies a destination network (or host) IP address, 

and the corresponding next-hop router that messages for the specified destination will be forwarded 
to.  It is assumed that the next-hop router (or 

gateway

) will then deliver the data to the required 

destination (or forward it on to another router that will). 

 

The above network diagram illustrates a situation where routing rules may need to be configured.  
In this example, the D2 W MDME 2400 clients need only specify the Access Point as their default 
gateway (i.e. they require no routing rules be configured).  However, for the Access Point to be able 
to deliver traffic to LAN B and LAN C, it needs to have routing rules configured that specify the 
respective D2 W MDME 2400 client/routers as next-hop routers (i.e. gateways) to networks B and 
C.  Note that devices on LAN A should specify the D2 W MDME 2400 Access Point as their 
default gateway.  An alternative to adding routing rules to the D2 W MDME 2400, in this example, 
would be for each device on LAN A that needs to communicate with LANs B and C to 
independently have routing rules specifying the D2 W MDME 2400 clients at B and C as gateways 
to those networks. 

The routing rules for the Access Point in the above example are shown below.  The first entry 
shows the route to LAN B.  The gateway for the route to LAN B is configured as the wireless IP 
address of the D2 W MDME 2400 client connected to LAN B.  The destination for the route is 
configured as the 

network

 address of LAN B.  Because the 

host

 ID of the destination IP address is 

0, it specifies a network address.  Consequently, any traffic received at the Access Point with 
destination IP address 169.254.109.x (where x is any host ID) will be forwarded to the D2 W 
MDME 2400 at LAN B.  

Client

Router

LAN  C

169.254.102.17

192.168.0.73

LAN A

 

Client

Bridge

Access Point 

Bridge

 

192.168.0.34

 

192.168.0.72

Client 

Router

LAN  B

169.254.109.40

192.168.0.74

Содержание D2 W MDME 2400 1






















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды