Congatec COM Express conga-BM67 Скачать руководство пользователя страница 86

Страница: 86 / 101

2011

congatec

BM67_BS67m02

86/101

9.5.2

Watchdog Configuration Submenu

Feature

Options

Description

POST Watchdog

Disabled

30sec
1min
2min
5min
10min
30min

Select the timeout value for the POST watchdog.

The watchdog is only active during the power-on-self-test of the system and provides a facility to prevent errors during boot up by
performing a reset..

Stop the Watchdog
for User Interaction

Yes

Select whether the POST watchdog should be stopped during the popup boot selection menu or while waiting for setup password
insertion.

Runtime Watchdog

Disabled

One time trigger
Single Event
Repeated Event

Selects the operating mode of the runtime watchdog. This watchdog will be initialized just before the operating system starts booting.

If set to ‘

One time trigger’

the watchdog will be disabled after the first trigger.

If set to

‘Single event’

, every stage will be executed only once, then the watchdog will be disabled.

If set to

‘Repeated event’

the last stage will be executed repeatedly until a reset occurs.

Delay

Disabled

10sec
30sec
1min
2min
5min
10min
30min

Select the delay time before the runtime watchdog becomes active. This ensures that an operating system has enough time to load.

Event 1

ACPI Event

Reset

Power Button

Selects the type of event that will be generated when timeout 1 is reached.

Event 2

Disabled

ACPI Event
Reset
Power Button

Selects the type of event that will be generated when timeout 2 is reached.

Event 3

Disabled

ACPI Event
Reset
Power Button

Selects the type of event that will be generated when timeout 3 is reached.

Timeout 1

1sec
2sec
5sec
10sec

30sec

1min
2min
10min
30min

Selects the timeout value for the first stage watchdog event.

Timeout 2

see above

Selects the timeout value for the second stage watchdog event.

Содержание COM Express conga-BM67






































































































Результаты поиска

Содержание COM Express conga-BM67

Отзывы:

Похожие инструкции для COM Express conga-BM67

Бренды по названию

Популярные бренды

Congatec COM Express conga-BM67, Руководство пользователя

Результаты поиска

Содержание COM Express conga-BM67

Отзывы:

Похожие инструкции для COM Express conga-BM67

Бренды по названию

Популярные бренды