Congatec COM Express conga-BM67 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 101

background image

Copyright

©

2011

congatec

AG

BM67_BS67m02

32/101

4.2.3

HDMI

The Intel

®

BD82QM67 or BD82HM65 (QM67 or HM65) PCH on the conga-BM67/BS67 supports integrated HDMI, which is multiplexed onto the

PCI Express Graphics (PEG) interface of the COM Express connector. The Intel

®

QM67 or HM65 provides three ports capable of supporting

HDMI. See section 7.5 of this document for more information about enabling HDMI peripherals.

Note

For more information about implementing a HDMI interface on COM Express™ carrier boards, refer to application note AN17_HDMI_DP_

Implementation.pdf, which can be found on the congatec website.

4.2.4

DisplayPort (DP)

The conga-BM67/BS67 offers three DP ports, each capable of supporting link-speeds of 1.62 Gbps and 2.7 Gbps on 1, 2 or 4 data lanes.

The DP is multiplexed onto the PCI Express Graphics (PEG) interface of the COM Express connector. The DisplayPort specification is a

VESA standard aimed at consolidating internal and external connection methods to reduce device complexity, supporting key cross industry
applications, and providing performance scalability to enable the next generation of displays. The Intel

®

BD82QM67 or BD82HM65 (QM67

or HM65) PCH can support a maximum of 2 DP ports simultaneously. See section 7.5 of this document for more information about enabling
DisplayPort peripherals.

Note

For more information about implementing a DisplayPort (DP) interface on COM Express™ carrier boards, refer to application note AN17_

HDMI_DP_Implementation.pdf, which can be found on the congatec website.

4.2.5

PCI Bus

The PCI bus is implemented using the Intel

®

certified Pericom PI7C9X113SL PCIe to PCI bridge and is connected via one of the eight PCI

Express lanes offered by the conga-BM67/BS67. The PCI bus complies with PCI specification Rev. 2.3 and provides a 32bit parallel PCI bus

that is capable of operating at 33MHz. The PCI bus provides support for up to 4 bus masters.

Note

The PCI interface is specified to be +5V tolerant, with +3.3V signaling.

«
...
30
31
32
33
34
...
»

Содержание COM Express conga-BM67






































































































Отзывы:

Нет отзывов

Похожие инструкции для COM Express conga-BM67

Бренд: Acer Страницы: 15

Бренд: Acer Страницы: 12

Бренд: ICP Страницы: 50

945GC MICRO 775

Бренд: Biostar Страницы: 49

Z690 Phantom Gaming 4

Бренд: ASROCK Страницы: 109

Бренд: Biostar Страницы: 85

DS-5116HFI Series

Бренд: HIKVISION Страницы: 22

Бренд: ASROCK Страницы: 144

LCMXO3L-DSI-EVN

Бренд: Lattice Страницы: 2

Бренд: Erreka Страницы: 4

Бренд: SMSC Страницы: 4

Бренд: Supero Страницы: 143

GA-8IP775 Series

Бренд: Gigabyte Страницы: 80

Бренд: IEI Technology Страницы: 21

Бренд: ASROCK Страницы: 92

Бренд: ASROCK Страницы: 2

Бренд: ASROCK Страницы: 57

K8M800 INFINITY

Бренд: DFI Страницы: 122

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды