Congatec COM Express conga-BM67 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 101

background image

Copyright

©

2011

congatec

AG

BM67_BS67m02

36/101

5.6.4

congatec Battery Management Interface

In order to facilitate the development of battery powered mobile systems based on embedded modules, congatec AG has defined an interface

for the exchange of data between a CPU module (using an ACPI operating system) and a Smart Battery system. A system developed according

to the congatec Battery Management Interface Specification can provide the battery management functions supported by an ACPI capable

operating system (e.g. charge state of the battery, information about the battery, alarms/events for certain battery states, ...) without the need

for any additional modifications to the system BIOS.

The conga-BM67/BS67 BIOS fully supports this interface. For more information about this subject visit the congatec website and view the

following documents:

• congatec Battery Management Interface Specification

•

Battery System Design Guide

•

conga-SBM²C User’s Guide

5.6.5

API Support (CGOS/EAPI)

In order to benefit from the above mentioned non-industry standard feature set, congatec provides an API that allows application software

developers to easily integrate all these features into their code. The CGOS API (congatec Operating System Application Programming Interface)
is the congatec proprietary API that is available for all commonly used Operating Systems such as Win32, Win64, Win CE, Linux and QNX. The

architecture of the CGOS API driver provides the ability to write application software that runs unmodified on all congatec CPU modules. All the

hardware related code is contained within the congatec embedded BIOS on the module. See section 1.1 of the CGOS API software developers
guide, which is available on the congatec website .

Other COM (Computer on Modules) vendors offer similar driver solutions for these kind of embedded PC features, which are by nature
proprietary. All the API solutions that can be found on the market are not compatible to each other. As a result, writing application software that
can run on more than one vendor’s COM is not so easy. Customers have to change their application software when switching to another COM

vendor. EAPI (Embedded Application Programming Interface) is a programming interface defined by the PICMG that addresses this problem.

With this unified API it is now possible to run the same application on all vendor’s COMs that offer EAPI driver support. Contact congatec

technical support for more information about EAPI.

«
...
34
35
36
37
38
...
»

Содержание COM Express conga-BM67






































































































Отзывы:

Нет отзывов

Похожие инструкции для COM Express conga-BM67

R0K5R8C34DK2HBR

Бренд: Renesas Страницы: 32

Бренд: J&W Страницы: 40

Бренд: ST Страницы: 22

Бренд: Emcore Страницы: 12

PCAN-MicroMod Evaluation Kit

Бренд: Peak Страницы: 18

Бренд: Gigabyte Страницы: 18

Бренд: Gigabyte Страницы: 36

z170a GAMING M9 ACK

Бренд: MSI Страницы: 109

Бренд: IEI Technology Страницы: 145

SBC81870 Series

Бренд: AXIOMTEK Страницы: 120

Бренд: Atmel Страницы: 59

Бренд: Advantech Страницы: 104

Бренд: Mercury Страницы: 42

Бренд: Sleipner Страницы: 24

Бренд: Carp Design Страницы: 6

Бренд: Winmate Страницы: 72

Бренд: Biostar Страницы: 55

SY-P4S DRAGON Ultra

Бренд: SOYO Страницы: 154

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды