manualshive.com logo in svg

Congatec COM Express conga-BM67, Руководство пользователя, Страница: 16 / 101

Поделиться
Скачать
Congatec COM Express conga-BM67 Скачать руководство пользователя страница 16

Copyright 

© 

2011 

congatec 

AG 

 

      BM67_BS67m02 

 

      

16/101

1.6 

Power Consumption

The power consumption values listed in this document were measured under a controlled environment. The hardware used for testing includes 

a conga-BM67/BS67 module, conga-Cdebug carrier board, CRT monitor, SATA drive, and USB keyboard. The conga-Cdebug is modified 

so that the 12V input is only routed to the module and all other circuity on the carrier itself is powered by the 5V input. The SATA drive was 

powered externally by an ATX power supply so that it does not influence the power consumption value that is measured for the module. The 

USB keyboard was detached once the module was configured within the OS. All recorded values were averaged over a 30 second time period. 

Cooling of the module was done by the module specific heatpipe heatspreader and a fan cooled heatsink to measure the power consumption 

under normal thermal conditions. 

The conga-Cdebug originally does not provide 5V standby power. Therefore, an extra 5V_SB connection without any external loads was made. 
Using this setup, the power consumption of the module in S3 (Standby) mode was measured directly. 

Each module was measured while running Windows 7 Professional 64Bit, Hyper Threading enabled, Speed Step enabled, CPU Turbo Mode 
enabled and Power Plan set to “Power Saver”. This setting ensures that Core™ processors run in LFM (lowest frequency mode) with minimal 
core voltage during desktop idle. Each module was tested while using two 1GB memory modules. Using different sizes of RAM, as well as one 
or two memory modules, will cause slight variances in the measured results.

To measure the worst case power consumption the cooling solution was removed and the CPU core temperature was allowed to run up to 
between 95° and 100°C while running 100% workload with the Power Plan set to “Balanced”. The peak current value was then recorded. This 

value should be taken into consideration when designing the system’s power supply to ensure that the power supply is sufficient during worst 

case scenarios. 

Содержание COM Express conga-BM67






































































































Отзывы:

Нет отзывов