Computec Door Drive 5.0 Скачать руководство пользователя страница 55

Страница: 55 / 63

Computec

CDD5.0

CDD 5.0: user manual – Rev.01

Page 55/63

Problem

Check

STEP

Question

Answer

Action

The system
switch on but
does not
move
properly

Movement
check in
Inspection
mode

Activate the Inspection
mode (press key 4 for
1s, or until INSP. Led is
on)

Door already closed by
external command (“CL”
fixed on the display).

Go to step 8

The display shows an
alarm (“AL” alternate to
alarm code)

Refer to alarms
table (paragraph
6.1)

Il display shows “- -“.

Go to step 8

Press and keep pressed
key 2 to open, then
press and keep pressed
key 3 to close and check
the panels movement

The door is moving
properly: it closed when
key 3 is pressed and
opens when key 2 is
pressed

Go to step 9

The door is not moving
and the display shows an
alarm (“AL” alternate to
alarm code)

Refer to alarms
table (paragraph
6.1)

The door is moving in
the opposite direction:
it’s closing instead
opening and opening
instead closing

Check the set
closing rotation and
correct parameter
P22. Then return to
step 7

Check opening profile.
Press and keep pressed
key 3 to close
completely the door,
until “CL” is shown fixed
on the display.
Then press and keep
pressed key 2 until the
door is completely open
(“Op” shown fixed)

The door opens correctly
with the set speed
profile

Go to step 10

The door opens with
reduced speed

The RSC command
(X3.1.22) is active.
Correct wiring or
settings

The door is not moving
and the display shows an
alarm (“AL” alternate to
alarm code)

Refer to alarms
table (paragraph
6.1)

The door is not moving
or is moving not properly

Apply the speed
profiles reset
(4.6.1.3). then
return to step 7

Check closing speed
profile.
Press and keep pressed
key 3 to close the door,
until the door is
completely closed (“CL”
shown fixed)

The door closes correctly
with the set speed
profile

Go to step 11

The door closes with
reduced speed

The RSC command
(X3.1.22) is active.
Correct wiring or
settings

The door is not moving
and the display shows an
alarm (“AL” alternate to
alarm code)

Refer to alarms
table (paragraph
6.1)

The door is not moving
or is moving not properly

Apply the speed
profiles reset
(4.6.1.3). then
return to step 7

Содержание Door Drive 5.0
































































Результаты поиска

Содержание Door Drive 5.0

Отзывы:

Computec Door Drive 5.0, Руководство пользователя, Страница: 55 / 63

Результаты поиска

Содержание Door Drive 5.0

Отзывы: