Computec Door Drive 5.0 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 63

Computec Door Drive 5.0 Скачать руководство пользователя страница 14

Computec

CDD5.0

EN

CDD 5.0: user manual – Rev.01

Page 14/63

To optimize the execution of the learning procedure, it
is suggested to couple car and landing door, executing
the operations from the car roof in inspection mode.

Press key

for at least 1s to enable Self-Learning.

Press shortly key

. The door starts opening with

reduced speed until the door is completely opened.

The learning phase is completed.

“SL” fixed

“SL” blinking
“OP” fixed

4

Speed Profiles
check in Inspection
mode

Press continuously key

to execute the door closing

with normal speed, until the door is completely closed.

Press continuously key

to execute the door

opening with normal speed, until the door is completely
opened.

In case it is necessary to tune the speed profiles, please
refer to the paragraph 5.2.1

Display visualization:

“CL” blinking
“CL” fixed

“OP” blinking
“OP” fixed

5

Obstacle reversing
check in Inspection
mode

Put an obstacle at different points of the door access.

Press and keep pressed key

to perform a door

closing.
When the panels meet the obstacle, the door drive will
immediately reverse the movement starting the
reopening.

Release key

during the reopening movement and

wait until the door is completely opened.

Display visualization:

“CL” blinking

“IM” blinking

“OP” fixed or
“- -“ blinking

«
...
12
13
14
15
16
...
»

Содержание Door Drive 5.0
































































Отзывы:

Нет отзывов