Computec Door Drive 5.0 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 63

Computec Door Drive 5.0 Скачать руководство пользователя страница 21

Computec

CDD5.0

EN

CDD 5.0: user manual – Rev.01

Page 21/63

4.3

HMI: front panel user interface

The CDD 5.0 door drive has a front panel that permits to activate different working modes: Normal,
Inspection and Configuration.

- Figure 4-2: front panel of the CDD5.0 door drive -

4.3.1

Display

The display (7-segment, two digits) present on the front panel permits the direct visualization of the drive
status and the current configurations, based on the active working mode. the following table reports the
main possible visualizations:

Digits

Description

Blinking: OPENING in progress
Fixed: Door OPENED

Blinking: CLOSING in progress
Fixed: Door CLOSED

The controller auto-set procedure is in progress

During the auto-set procedure an error occurred, the procedure has been interrupted
and it must be restarted.

Blinking: door Self-learning active but not in progress
Fixed: Self-learning opening movement in progress

Blinking: forced closing with reduced speed is in progress

Alarm active, alternate to the alarm code.

Blinking: reversing movement in progress
Fixed: an external reversing source is active, with door opened.

--

This means all the following:
- the door drive is waiting for a command
- the door panels are at intermediate position (not opened and not closed)
- the door drive is not receiving any command from the elevator controller

- Table 14: mean visualizations on the front panel display -

«
...
19
20
21
22
23
...
»

Содержание Door Drive 5.0
































































Отзывы:

Нет отзывов