Compaq TL891 - DLT Tape Library Скачать руководство пользователя страница 189 | Manualshive

Страница: 189 / 208

Compaq TL891 - DLT Tape Library Скачать руководство пользователя страница 189

Compaq Confidential – Need to Know Required

Writer: Everett Godaire Project: TL891 MiniLibrary System User's Guide Comments:

Part Number: ER-TL891-UA.A01 File Name: o-appg Information on Pass-Through Section Covers Last Saved On: 3/1/99 2:19 PM

Appendix

G

Information on Pass-Through Section

Covers

This appendix supplements the information presented in the section entitled
Mechanical Installation in Chapter 3.

IMPORTANT:

These procedures should be performed by a qualified service technician.

Pass-Through Section Covers

The Pass-Through mechanism moves tape cartridges vertically between
TL891 MiniLibrary modules. Each module section is covered by an individual
sheet-metal enclosure. These covers protect the mechanism during shipping
and are an important safety shield during operation.

A separate detachable side plate is part of the cover assembly. During
installation the side plates should be removed on any mechanism sections
located behind a MiniLibrary module; this allows easy access to a cartridge
stranded in transit by a commercial power outage. The remaining portion of
the cover can be removed also from any section behind a module.

IMPORTANT:

Both parts of the covers must remain in place over any section of the

mechanism that is not behind a MiniLibrary module. Any gaps between modules should
remain completely covered.

Figure G-1 shows the cover assembly side plate (1) and Figure G-2 shows the
mechanism section cover (2).

«
...
187
188
189
190
191
...
»

Содержание TL891 - DLT Tape Library

















































































































































































































Отзывы:

Нет отзывов